Related Manuals for New Holland T4020V
Summary of Contents for New Holland T4020V
- Page 1 SERVICE MANUAL T4020V / T4030V / T4040V / T4050V / T4060V T4030N / T4040N / T4050N / T4060N Print No. 84150905B1...
- Page 2 These pages replace the corresponding pages in the Manual of mod. T4020V - - T4030V - - T4030N - - T4040V - - T4040N - - T4050V - - T4050N: -- Content, pages 3, 4, 5, 6, 7, 8, 9 and 10.
- Page 3 Find manuals at https://best-manuals.com...
- Page 4 T4020V - - T4030V - - T4030N - - T4040V - - T4040N - - T4050V - - T4050N - - T4060V - - T4060N TRACTORS SERVICE MANUAL SECTIONS GENERAL GUIDELINES .........
- Page 5 1st update 84150905A1 - - 2nd update 84150905A2 - - etc. ◊ The information contained in this manual was current on the date printed on each section. As NEW HOLLAND constantly improves its product range, some information may be out of date subsequent to modifications im- plemented for technical or commercial reasons, or to meet legal requirements in different countries.
- Page 6 INTRODUCTORY NOTE This booklet completes the Repair Manual for the models T4020V - - T4030V - - T4030N - - T4040V - - T4040N - - T4050V - - T4050N with the inclusion of the new models T4060V and T4060N.
- Page 7 Find manuals at https://best-manuals.com...
- Page 8 ... 98--99 10--08 34--35--36-- 37--38--39-- CHAPTER 2 - - Engine models T4020V, T4030V, 40--41--42-- T4030N, T4040V and T4040N 43--44--45-- Summary ....1...
- Page 9 INDEX Page Date Page Date Gearbox driving and driven 18 - - CLUTCH shafts end float adjustment. 28 10--08 Sealing compound applica- Specifications ... 1--2 10--08 tion diagram ... . 29 10--08 tightening torques .
- Page 10 INDEX Page Date Page Date Disassembly--Assembly -- Disassembly--Assembly -- clutch casing ... 22--23--24-- front epicyclic final drive 25--26 10--08 with brake ....36--37--38-- 10--08 23 - - DRIVE LINES Disassembly--Assembly --...
- Page 11 INDEX Page Date Page Date Checking leading wheel 31 - - POWER TAKE- -OFF alignment ....50 06--06 Steering sensor replace- CHAPTER 1 - - Mechanical power take- -off ment .
- Page 12 INDEX Page Date Page Date Sections ....6--7--8--9-- Description and operation 11--12--13-- 10--08 14--15--16-- 10--08 Description and operation 11--12--13-- 10--08 Removal--Installation -- lift 18--19--20-- 10--08 Troubleshooting ..15--16 10--08 Draft sensor support.
- Page 13 INDEX Page Date Page Date Disassembly--Assembly -- Disassembly--Assembly -- hydrostatic control valve . . 12--13--14-- Front PTO transmission 15--16--17-- shaft ....26 02--12 18--19--20-- Front PTO casing cross--...
- Page 14 INDEX Page Date Page Date Testing operation and cool- CHAPTER 2 - - Components ing ....14--15 10--08 Components ... . 2--3--4--5--6 conditioning system 10--08...
- Page 15 INDEX Page Date Page Date Platform assembly. CHAPTER 8 - - Connectors Removal -- Installation . . . 4--5--6--7-- 8--9--10--11 10--08 Content ....1 02--12 Dashboard .
- Page 16 SECTION 00 - - GENERAL - - CHAPTER 1 START UP to penetrate the skin. Therefore, NEVER USE HANDS TO CHECK FOR LEAKS, but use a Never run the engine in confined spaces that are piece of cardboard or wood for this purpose. If not equipped with adequate ventilation for ex- any liquid penetrates skin tissue, call for medical haust gas extraction.
- Page 17 Fuel tank ....Decanted, filtered Reduced fuel tank ..diesel fuel Engine oil sump: NH 330H T4020V, T4030V, AMBRA (SAE 15W--40) API CH4 T4040V, T4030N, T4040N MASTERGOLD...
- Page 18 SECTION 10 - - ENGINE - - CHAPTER 1 SECTION 10 - - ENGINE Chapter 1 - - Engine (mod. T4050V- - T4050N - -T4060V and T4060N) INDEX Section Description Page 10 000 General specifications ............Specifications .
- Page 19 SECTION 10 - - ENGINE - - CHAPTER 1 GENERAL SPECIFICATIONS Engine, technical type: mod. T4050V and T4050N -- type F4CE9484M*J602 (BOSCH pump) mod. T4060V and T4060N -- type F4CE9484L*J603 F4CE9484L*J602 (BOSCH pump) Cycle ..........diesel, 4--stroke Fuel injection .
- Page 20 SECTION 10 - - ENGINE - - CHAPTER 1 (overleaf) GENERAL SPECIFICATIONS Cooling ..........coolant circulation Radiator .
- Page 21 SECTION 10 - - ENGINE - - CHAPTER 1 (overleaf) GENERAL SPECIFICATIONS BOSCH Injection pump ....... . . rotating distributor type All--speed governor, incorporated in pump: BOSCH .
- Page 22 SECTION 33 - - BRAKING SYSTEM - - CHAPTER 1 SECTION 33 - - BRAKES Chapter 1 - - Brakes CONTENTS Section Description Page 33 000 Main data ..............Tightening torques .
- Page 23 T4030V, T4040V, T4050V and T4060V ..... . Front final drive -- bevel drive casing retaining bolts (C mod. T4020V, T4030V, T4040V, T4050V and T4060V ..11.2 Bevel drive support retaining bolts (C ) mod.
- Page 24 SECTION 33 - - BRAKING SYSTEM - - CHAPTER 1 PARKING LOCKING ON THE TRANSMISSION Removal- -Installation WARNING Handle all parts with care. Do not put your hands or fingers between parts. Wear the prescribed safety clothing, including goggles, gloves and safety footwear.
- Page 25 SECTION 33 - - BRAKING SYSTEM - - CHAPTER 1 5. Disconnect the electric connection (1) of the parking locking sensor on the transmission. 6. Disconnect the differential lock control pipe. 7. Unscrew the retaining screws and remove the control lever assembly (1) for parking locking on the transmission.
- Page 26 SECTION 33 - - BRAKING SYSTEM - - CHAPTER 1 PARKING LOCKING ON THE TRANSMISSION Adjustment WARNING Use suitable tools to align the holes. NEVER USE FINGERS OR HANDS. Proceed as follows. Before starting adjustment, detach the control rod completely. 1.
- Page 27 SECTION 33 - - BRAKING SYSTEM - - CHAPTER 1 84150905AB1 - - 02 - - 2012...
- Page 28 SECTION 35 - - HYDRAULIC SYSTEMS - - CHAPTER 6 SECTION 35 - - HYDRAULIC SYSTEMS Chapter 6 - - Front power take- -off and electronic lift (for T4030N, T4040N, T4050N and T4060N models) CONTENT Operation Description Page Main data .
- Page 29 SECTION 35 - - HYDRAULIC SYSTEMS - - CHAPTER 6 MAIN SPECIFICATIONS OF ELECTRONICALLY CONTROLLED FRONT LIFT (overleaf) 34.936 ÷ 34.975 Diameter of arm lifting shaft (14, fig. 4) in relation to bushings . . 35.140 ÷ 35.180 Internal diameter of bushings (15) fitted on lift body ... 40.060 ÷...
- Page 30 SECTION 35 - - HYDRAULIC SYSTEMS - - CHAPTER 6 IMPLEMENT HITCHING DEVICE DATA (overleaf) Type ........... . three--point linkage Category: Working depth control .
- Page 31 SECTION 35 - - HYDRAULIC SYSTEMS - - CHAPTER 6 84150905AB1 - - 02 - - 2012...
- Page 32 SECTION 35 - - HYDRAULIC SYSTEMS - - CHAPTER 6 MDC0801A 84150905B1 - - 02 - - 2012...
- Page 33 SECTION 35 - - HYDRAULIC SYSTEMS - - CHAPTER 6 Longitudinal and cross- -sectional views of implement linkage assembly Implement linkage third point hook. Attaching Bolts. Third point top link. Lift arms. Implement linkage assembly. Arms lateral clearance return bolt. Arms longitudinal position pin.
- Page 34 SECTION 35 - - HYDRAULIC SYSTEMS - - CHAPTER 6 Longitudinal and cross- -sectional views of implement linkage assembly Lift arms position sensor. 13. Pin retaining bolt (14). 10. Top link third point pivot pin. 14. Lift arms pivot pin. 11.
- Page 35 SECTION 35 - - HYDRAULIC SYSTEMS - - CHAPTER 6 Longitudinal and cross- -sectional views of front power take- -off Power take--off shaft guard Constant velocity joint guard. Power take--off shaft Constant velocity joint. Electromagnetic Clutch. PTO gears casing. Electromagnetic clutch bearings. Mechanical power take--off.
- Page 36 SECTION 35 - - HYDRAULIC SYSTEMS - - CHAPTER 6 Longitudinal views of shaft with front power take- -off electromagnetic clutch Power take--off shaft Constant velocity joint coupler flange. Thrust washer with snap ring Clutch ring/spring retaining bolts. Power take--off electromagnetic clutch bearings.. Constant velocity joint.
- Page 37 SECTION 35 - - HYDRAULIC SYSTEMS - - CHAPTER 6 Longitudinal views of front power take- -off casing Gearbox. Retaining Ring. Seal. Thrust washer. Retaining Ring. 10. Engagement sleeve return spring. Engagement shaft and sleeve. 11. Power take--off driven gear. Power take--off driving flange.
- Page 38 SECTION 35 - - HYDRAULIC SYSTEMS - - CHAPTER 6 ELECTROMAGNETICALLY ENGAGED FRONT LIFT AND POWER TAKE- -OFF Description And Operation The mechanical lift can operate with the implement Using the pushbutton (3) the implement can be in the controlled position, after having adjusted the raised and lowered without using the previously travel and raising limits with potentiometers (11) and adjusted potentiometers (11) and (12).
- Page 39 SECTION 35 - - HYDRAULIC SYSTEMS - - CHAPTER 6 FRONT LIFT Operation controls Two potentiometers (1 and 2 fig. 9) are located on the left--hand side of the dashboard, allowing the upper limit and working position to be stabilised. Switch (1, fig.
- Page 40 SECTION 35 - - HYDRAULIC SYSTEMS - - CHAPTER 6 FRONT POWER TAKE OFF DANGER Before using the tractor, check that the plastic guard (1, fig. 11) is in perfect condition and fitted on the universal joint. DANGER In order to ensure longer life for the coupling and the electromagnetic clutch, when the front power take- -off is not being used, select the neutral position by turning the screw (1, fig.
- Page 41 This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...