Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PTNS 10-3 6V
Summary of Contents for Trotec PTNS 10-3 6V
- Page 1 PTNS 10-3,6V ORIGINAL INSTRUCTIONS CORDLESS TACKER...
-
Page 2: Table Of Contents
EU declaration of conformity via the following link: Declaration of conformity ........... 14 PTNS 10-3,6V Notes regarding the instructions Symbols https://hub.trotec.com/?id=41135 Warning of electrical voltage This symbol indicates dangers to the life and health of Safety persons due to electrical voltage. -
Page 3: Safety
• Dress properly. Do not wear loose clothing or General Power Tool Safety Warnings – Electrical jewellery. Keep your hair and clothing away from safety moving parts. Loose clothes, jewellery or long hair can be • Power tool plugs must match the outlet. Never modify caught in moving parts. - Page 4 • Only charge the Li-Ion battery (capacity of 1.5 Ah = General Power Tool Safety Warnings – Battery tool 1 battery cell) that is permanently installed in the cordless use and care tacker with the "PTNS 10-3.6V AC" charger. The battery • Recharge only with charger specified by the voltage must match the battery charging voltage of the manufacturer.
- Page 5 We recommend using the power tool with original Trotec Warning of electrical voltage accessories. There is a risk of a short-circuit due to liquids...
- Page 6 Caution Vibration emissions can cause a health hazard if the device is used for an extended period of time or if it is not properly handled and maintained. Caution Keep a sufficient distance from heat sources. Note If you store or transport the device improperly, the device may be damaged.
-
Page 7: Information About The Device
Information about the device Device description PTNS 10-3,6V is a cordless tacker designed for tacking insulating material or decoration. You can staple and tack cardboard, leather, textile or natural fibres and similar materials onto softwood or material similar to wood. A shot sequence of 30 shots per minute can be accomplished. -
Page 8: Transport And Storage
Technical data Information on noise and vibration: • The vibration level specified in these instructions was Parameter Value determined by means of a measuring method standardized in EN 60745 and can be used for a device comparison. The Model PTNS 10-3.6 V specified vibration emission value may also be used for a Nominal voltage 3.6 V... -
Page 9: Start-Up
The battery is partially charged upon delivery to avoid damage Storage to the battery caused by a deep discharge. Before storing the device, observe the following: The battery should be charged prior to initial start-up and when • Switch off the device. the battery is low (the battery level indication (8) is illuminated •... - Page 10 Filling the magazine Warning of electrical voltage Before any work on the device, remove the mains plug of the charger from the mains socket! Hold onto the mains plug while pulling the power cable out of the mains socket. Warning Make sure that the battery has been removed from the device! Make sure not to hold the device by the trigger when a...
-
Page 11: Operation
5. Slide the magazine slider (5) back down alongside the Operation magazine (12) until it clicks into place. Tips and notes on handling the tacker Warning of sharp object Wire nails and staples are sharp. Risk of injuries if handled without due care! General information: •... -
Page 12: Errors And Faults
Contact the Trotec customer service. • Check the charger connection for dirt. Remove any dirt. • The battery might be defective. Contact the Trotec customer service. A wire nail or staple is jammed in the device:... -
Page 13: Maintenance
Do not touch the mains plug of the charger with wet or that apply for many EU countries on the website damp hands. https://hub.trotec.com/?id=45090. Otherwise, please contact an • Switch the device off. official recycling centre for electronic and electrical equipment •... -
Page 14: Declaration Of Conformity
Declaration of conformity Declaration of conformity in accordance with the EC Machinery Directive 2006/42/EC, Annex II, Part 1, Section A We – Trotec GmbH – declare in sole responsibility that the product designated below was developed, constructed and produced in compliance with the requirements of the EC Machinery Directive in the version 2006/42/EC. - Page 15 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...