Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PRDS 20-230V
Summary of Contents for Trotec PRDS 20-230V
- Page 1 PRDS 20-230V ORIGINAL INSTRUCTIONS CHISEL HAMMER...
-
Page 2: Table Of Contents
Info Information marked with this symbol helps you to carry out your tasks quickly and safely. Follow the manual Information marked with this symbol indicates that the instructions must be observed. Chisel hammer PRDS 20-230V... -
Page 3: Safety
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. Chisel hammer PRDS 20-230V... - Page 4 • Keep all traffic, rescue and escape routes clear. Widely • Use the additional handle pre-assembled at the device. cordon off danger areas. Losing control of the power tool may result in personal injury. Chisel hammer PRDS 20-230V...
- Page 5 Electric shock due to insufficient insulation! whilst adhering to the technical data. Check the device for damages and proper functioning We recommend using the power tool with original Trotec before each use. accessories. If you detect damages, do not use the device any longer.
-
Page 6: Information About The Device
Hold onto the mains plug while pulling the power Two-hole spanner cable out of the mains socket. SDS flat chisel 3. Do not reconnect a defective device to the mains. SDS pointed chisel Lubricant container Additional handle Chisel hammer PRDS 20-230V... - Page 7 Sound values according to EN 62841 Sound pressure level L 95 dB(A) Sound power level L 101 dB(A) Uncertainty K 3 dB(A) Vibration information according to EN 62841 Vibration emission value for 10.19 m/s chiselling a Uncertainty K 1.5 m/s Chisel hammer PRDS 20-230V...
-
Page 8: Transport And Storage
• Dry and protected from frost and heat (e.g. the flat chisel, (5)) from the tool holder. • Ambient temperature below 45 °C ð You can then release the tool holder again. • Protected from dust and direct sunlight inside the transport case Chisel hammer PRDS 20-230V... - Page 9 Please proceed as follows to adjust the position of the additional 1. Insert the mains plug into a properly secured mains handle: socket. 1. Loosen the additional handle (8). ð The tensioner at the additional handle releases. Chisel hammer PRDS 20-230V...
-
Page 10: Operation
5. Wait until the device has stopped before putting it away. 4. Press the on/off switch (3) again to deactivate continuous operation. ð The button for continuous operation (2) automatically returns back into its initial position. 5. Let go of the on-/off-switch (3) to stop the device. Chisel hammer PRDS 20-230V... -
Page 11: Errors And Faults
• This is not a fault. These phenomena disappear after a opened must only be carried out by authorised brief runtime. specialist companies or by Trotec. The device does not start: Lubricating the tool holder • Check the power connection. -
Page 12: Disposal
• Dry the flat chisel (5) and the pointed chisel (6) with a soft, lint-free cloth. • Keep the ventilation openings free from dust deposits to prevent overheating of the motor. • Slightly grease the tool holder with machine lubricant before inserting another tool. Chisel hammer PRDS 20-230V... -
Page 13: Declaration Of Conformity
Declaration of conformity Declaration of conformity in accordance with the EC Machinery Directive 2006/42/EC, Annex II, Part 1, Section A We – Trotec GmbH – declare in sole responsibility that the product designated below was developed, constructed and produced in compliance with the requirements of the EC Machinery Directive in the version 2006/42/EC. - Page 14 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...