Outdoor Twinning Kit - Mitsubishi Electric CITY MULTI PQRY-P72-336ZLMU-A1 Data Book

9. OPTIONAL PARTS

9-2. OUTDOOR TWINNING KIT

The following optional Outdoor Twinning Kit is needed to use to combine multiple refrigerant pipes. Refer to section "Piping Design"
for the details of selecting a proper twinning kit.
CMY-Q100CBK2
Low-pressure pipe twinning kit
27(1-2/16)
ø28.58(ø1-1/8)
(Outside diameter)
ø22.2(ø7/8)
(Outside diameter)
High-pressure twinning pipe
ø19.05(ø3/4)
ø22.2(ø7/8)
ø19.05(ø3/4)
80(3-3/16)
CMY-Q200CBK
Low-pressure pipe twinning kit
77(3-1/16)
ø31.75(ø1-1/4)
(Outside diameter)
High-pressure twinning pipe
ø19.05(ø3/4)
ø28.58(ø1-1/8)
ø19.05(ø3/4)
80(3-3/16)
Note 1. Reference the attitude angle of the twinning pipe below the fig.
The angle of the twinning pipe is within ±15° against the horizontal plane.
2. Use the attached pipe to braze the port-opening of the twinning pipe.
3. Pipe diameter is indicated by inside diameter.
MEES21K047
<Elbow pipe(Accessory)>
315(12-7/16)
45(1-13/16)
ø25.4(ø1)
<Pipe for routing through the front (Accessory)>
ø28.58(ø1-1/8)
(Outside diameter)
<Pipe for routing through the front (Accessory)>
ø19.05(ø3/4)
ø19.05(ø3/4)
65
(2-9/16)
135(5-1/4)
<Elbow pipe(Accessory)>
407(16-1/16)
50(2)
72(2-7/8) ø28.58(ø1-1/8)
<Pipe for routing through the front (Accessory)>
ø31.75(ø1-1/4)
(Outside diameter)
ø34.93(ø1-3/8)
(Outside diameter)
ø28.58(ø1-1/8)
(Outside diameter)
<Deformed pipe(Accessory)>
ø19.05(ø3/4) ø22.2(ø7/8)
(Outside diameter)
62
(2-1/2)
<Pipe for routing through the front (Accessory)>
66 185(7-5/16)
(2-5/8)
ø19.05(ø3/4)
ø25.4(ø1)
Twinning pipe
<Accessory>
ø28.58(ø1-1/8)
ø28.58(ø1-1/8)
50(2)
ø22.2(ø7/8)
ø22.2(ø7/8)
36(1-7/16)
ø34.93(ø1-3/8)
187(7-6/16)
Note 1. Refer to the figure below for the installation
position of the high-pressure twinning pipe.
Inclination tolerance of the
high-pressure twinning pipe is ±15°
relative to the ground.
2. Pipe diameter is indicated
53
by inside diameter.
(2-1/8)
<Accessory>
ø28.58(ø1-1/8) ø31.75(ø1-1/4)
ø31.75(ø1-1/4)
ø28.58(ø1-1/8)
53(2-1/8)
ø34.93(ø1-3/8)
ø28.58(ø1-1/8)
160(6-5/16)
(Outside diameter)
ø41.28(ø1-5/8)
215(8-1/2)
69
(2-3/4)
Note 1. Refer to the figure below for the installation
position of the high-pressure twinning pipe.
High-pressure twinning pipe
On-site pipes
Inclination tolerance of the
high-pressure twinning pipe is ±15°
relative to the ground.
2. Pipe diameter is indicated
by inside diameter.
WR2-Series-575V
Fixing screw • • • 1
Insulation cover • • • 1
Pipe cover (150mm(5-15/16) Length) • • • 2
Pipe cover (60mm(2-3/8) Length) • • • 1
Pipe cover (80mm(3-3/16) Length) • • • 2
Cable tie • • • 2
Water stopper • • • 1
Sealing material (Small) • • • 1
Sealing material (Large) • • • 1
High-pressure twinning pipe
On-site pipes
Fixing screw • • • 1
Insulation cover • • • 1
Pipe cover (75mm(3) Length) • • • 1
Pipe cover (360mm(14-3/16) Length) • • • 1
Pipe cover (70mm(2-13/16) Length) • • • 1
Pipe cover (130mm(5-1/8) Length) • • • 1
Pipe cover (100mm(3-15/16) Length) • • • 1
Pipe cover (160mm(6-5/16) Length) • • • 1
Cable tie • • • 2
Water stopper • • • 1
Sealing material (Small) • • • 1
Sealing material (Large) • • • 1
ø28.58(ø1-1/8)
91