Subscribe to Our Youtube Channel
Related Manuals for Aero-Spa QT 800
Summary of Contents for Aero-Spa QT 800
- Page 1 Installation Guide For additional assistance please contact us at: Technical Support 877-226-8111 info@aero-spa.net...
- Page 2 1 PPM residual chlorine sanitizer in the water at all times. The best industry practice will minimize the possibility of cross contamination; however; will not eliminate possibility. © Copyright Aero-Spa®, LLC 2021 REV H...
-
Page 3: Important Safety Instructions
Read and follow all instruction. Never operate Aero-Spa equipment indoors. Do not use hot tub for 30 minutes after the Aero-Spa unit has operated. Never inhale ozone exhausted by Aero-Spa unit. Follow all electrical installation instructions in this installation guide. -
Page 4: Equipment Identification
Please note that your product may vary from photos in this installation guide. Aero-Spa™ Generator Cycle Timer 20 feet – Ozone Tube with Diffuser Model: AP 1000 DESCRIPTION Aero-Spa™ Generator 20 feet – Ozone Tube Sintered Diffuser Cycle Timer © Copyright Aero-Spa®, LLC 2021 REV H... -
Page 5: Equipment Setup
For best results it is highly recommended that the hot tub be drained and thoroughly cleaned to remove residual dirt and contaminants prior to installation of the Aero-Spa system. Set the equipment on a level solid spacer block that is at least 2 – 3/8”... -
Page 6: Grounding Instructions
10’ from the hot tub that can be used to supply power to the equipment 6.) Insert the electrical plug from the Aero-Spa into provided cycle timer. Adjust the timer to operate 2 hours of run time 2 times per day. - Page 7 When the product cools it will automatically restart. Only if required, obtain a UL outdoor rated extension cord. Never locate the Aero-Spa generator closer than 10’ from the hot tub. In the event of a power outage, the GFCI device will need to be reset manually.
-
Page 8: Maintenance And Care
The diffuser stone can be cleaned with a 2% hydrogen peroxide solution or muriatic acid. Fill & Start-Up Recommendations Our customers have been using the Aero-Spa system as the primary water treatment process for years without harsh chemicals. Because we cannot control how your hot tub is used/maintained and according to the EPA we must recommend maintaining at 1 –... -
Page 9: Troubleshooting
2. Bypass timer, if this corrects the problem, replace timer 3. Verify ozone tube is not broken, pinched, or disconnected 4. If these steps do not solve the problem call Aero-Spa, LLC Water is cloudy A condition typically associated with organic particulates from oils, soaps, or materials inside piping of the hot tub. - Page 10 If there is more than a few drops proceed to step 2. below 2. Turn off all power by unplugging Aero-Spa from the 120 volt power outlet. Remove the sintered diffuser from the hot tub and lay it on the ground at a lower elevation than the generator.
-
Page 11: Manufacturer's Limited Warranty
If during the first ninety days you are not satisfied with the water quality in your hot tub or pool you can return the Aero-Spa™ product to us for a refund. All other unused products and accessories returned are subject to a twenty-five percent restocking fee and must be returned within fourteen days of purchase. - Page 12 W300 N7706 Christine Lane, Hartland, Wisconsin, 53029, visit our website at www.aero- spa.net or e-mail us at info@aero-spa.net. If Buyer is making a warranty claim, please provide a description of the nature of the problem. Alternatively, call the following toll-free number to obtain further warranty instructions: 1-877-226-8111.
Need help?
Do you have a question about the QT 800 and is the answer not in the manual?
Questions and answers