Download Print this page
Aero-Spa AP 1000 Installation Manual
Hide thumbs Also See for AP 1000:

Advertisement

Quick Links

Installation Guide
Manufactured for Aero-Spa™, LLC
E-Mail:
info@aero-spa.net
Web: www.aero-spa.net

Advertisement

loading
Need help?

Need help?

Do you have a question about the AP 1000 and is the answer not in the manual?

Questions and answers

Summary of Contents for Aero-Spa AP 1000

  • Page 1 Installation Guide Manufactured for Aero-Spa™, LLC E-Mail: info@aero-spa.net Web: www.aero-spa.net...
  • Page 2 1 PPM residual chlorine sanitizer in the water at all times. The best industry practice will minimize the possibility of cross contamination; however; will not eliminate possibility. © Copyright Aero-Spa®, LLC 2013 P/N102203 rev G...
  • Page 3: Important Safety Instructions

     Read and follow all instruction.  Never operate Aero-Spa™ equipment indoors.  Do not use hot tub for 30 minutes after the Aero-Spa™ unit has operated.  Never inhale ozone exhausted by Aero-Spa™ unit.  Follow all electrical installation instructions in this installation guide.
  • Page 4 Installation Aero-Spa™ Guide Generator Cycle Timer 20 feet – Ozone Tube Sintered Diffuser Model: AP 1000 DESCRIPTION Aero-Spa™ Generator 20 feet – Ozone Tube Sintered Diffuser Installation Guide Cycle Timer © Copyright Aero-Spa®, LLC 2013 P/N102203 rev G...
  • Page 5 Aero-Spa™ system. The system should be cleaned with Aero-Spa™ pipe cleaner and filled with filtered water through the Aero-Spa™ Fill Filter. The hot tub filter element should be replaced or cleaned using the Aero-Spa™ filter cleaner.
  • Page 6 Check with a qualified electrician or serviceman if the grounding Figure 6 instructions are not completely understood, or if in doubt as to whether © Copyright Aero-Spa®, LLC 2013 P/N102203 rev G...
  • Page 7 Only if required, obtain a UL outdoor rated extension cord Never locate the Aero-Spa™ generator closer than 10’ from the hot tub. d) Insert the electrical plug from the Aero-Spa™ into the extension cord. e) Insert the GFCI & Surge Protector Plug (Figure 7) into the electrical outlet identified in step 3) Figure 5.
  • Page 8 Restart product (see section 3)g). Fill & Start-Up Recommendations Our customers have been using the Aero-Spa™ system as the primary water treatment process for years without harsh chemicals. Because we cannot control how your hot tub is used/maintained and according to the EPA we must recommend maintaining at 1 –...
  • Page 9: Troubleshooting

    2. Reset circuit breaker at house fuse panel. If this problem persists call Aero-Spa™, LLC 3. Bypass timer, if this corrects the problem replace timer 4. If these steps do not solve the problem call Aero-Spa™, LLC Water is cloudy 1. Increase the run time cycle 2.
  • Page 10 2. If these steps do not solve the problem call Aero-Spa™, LLC Brown ring at water line 1. This is normal when the water used to fill the hot tub has high iron content.
  • Page 11 CUSTOMER SATISFACTION POLICY We are confident that the Aero-Spa™ process will maintain the desired water quality in your hot tub or pool. If during the first ninety days you are not satisfied with the water quality in your hot tub or pool you can return the Aero-Spa™...
  • Page 12 RIGHTS WHICH VARY FROM STATE TO STATE. To the extent that state law renders any provision in this warranty inoperative, state law shall apply and that clause shall be severed from the warranty; this severance, however, does not render the entire warranty inoperative. NOTES: © Copyright Aero-Spa®, LLC 2013 P/N102203 rev G...