Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Velleman-Kit Manuals
  4. Portable Generator
  5. K8044
  6. Illustrated assembly manual

Velleman-Kit K8044 Illustrated Assembly Manual

12v, ten channel light effect generator
Hide thumbs

Advertisement

Quick Links

Download this manual
Total solder points: 293
Difficulty level:
beginner 1o 2o 3þ 4o 5oadvanced
12V, Ten channel light
effect generator
Features:
þ
Ten, 12V/400mA outputs.
þ
To control cold-cathode fluorescent lamps (using FLPS adapter), light
bulbs, LED's and "solid state" relays, ...
þ
For use as advertisement lighting, party lights, discos, eye-catcher,...
þ
Ten pre-programmed light patterns selectable with a push button.
þ
The number of used channels is adjustable.
þ
Adjustable speed.
þ
Led indication for every output.
þ
12V operation possible for use in cars.
Specifications :
Power supply : 12V DC
•
Outputs : 12V DC/400mA per channel (Total : max 4A)
•
Dimensions : 140 x 100 x 27mm / 5,5 x 3,9 x 1,1"
•
Options (Velleman ordernumbers) :
Ú Power supply for cold-cathode fluorescent lamps : FLPS (300mm) or
FLPS1 (100mm)
Ú Cold-cathode fluorescent lamps : FL(xx) – (100 or 300mm).
Modifications reserved.
ILLUSTRATED ASSEMBLY MANUAL
K8044
H8044IP-1

Advertisement

loading

Related Manuals for Velleman-Kit K8044

Summary of Contents for Velleman-Kit K8044

  • Page 1 Total solder points: 293 Difficulty level: beginner 1o 2o 3þ 4o 5oadvanced 12V, Ten channel light effect generator K8044 Features: þ Ten, 12V/400mA outputs. þ To control cold-cathode fluorescent lamps (using FLPS adapter), light bulbs, LED’s and “solid state” relays, ...
  • Page 2 VELLEMAN Components NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be www.velleman-kit.com...
  • Page 3 Assembly hints 1. Assembly (Skipping this can lead to troubles ! ) Ok, so we have your attention. These hints will help you to make this project success- ful. Read them carefully. 1.1 Make sure you have the right tools: A good quality soldering iron (25- •...
  • Page 4 Assembly hints 1.3 Soldering Hints : Mount the component against the PCB surface and carefully solder the leads Make sure the solder joints are cone-shaped and shiny Trim excess leads as close as possible to the solder joint AXIAL COMPONENTS ARE TAPED IN THE CORRECT MOUNTING SEQUENCE ! REMOVE THEM FROM THE TAPE ONE AT A TIME !
  • Page 5 C O L O R = 2 … 5 COLOR= 2...5 4K7= ( 4 - 7 - 2 - B ) 4K7= ( 4 - 7 - 0 - 1 - 1 ) CODICE CODIGO CODIGO VÄRI FÄRG FARVE- FARGE- FARB COLOUR CODIFI-...
  • Page 6 Construction 1. Jumper q CH... : depending on the number of channels q RX ‘ ∗ ’ ‘∗’ ATTENTION : In case you use light bulbs, Cold-Cathode fluorescent lamps & “solid-state” relays mount for RX a jumper wire, If using LED’s as output indication then mount for RX a resistor appropriated to the value of the LED.
  • Page 7 Construction q R30 : 4K7 (4-7-2-B) 3. Resistors q R31 : 47 (4-7-0-B) R... q R32 : 3K3 (3-3-2-B) q R33 : 10K (1-0-3-B) q R34 : 10K (1-0-3-B) q R35 : 10K (1-0-3-B) q R1 : 10K (1-0-3-B) q R36 : 330 (3-3-1-B) q R2 : 10K (1-0-3-B) q R3 : 10K (1-0-3-B) 4.

  • Page 8: Voltage Regulator

    Construction 5. Pushbuttons. 8. LED. Watch the polarity ! COLOR= 2...5 LD... CATHODE q LD1 : 5mm Red q SW1 : S500 q SW2 : S500 q LD2 : 5mm Red q LD3 : 5mm Red q LD4 : 5mm Red 6.
  • Page 9 Construction Electrolytic capacitors. 10. Transistors. Watch the polarity ! C ... q T1 : BC640 q T2 : BC640 q T3 : BC640 q C5 : 10µF q T4 : BC640 q C3 : 220µF q T5 : BC640 q C1 : 1000µF / 25V q T6 : BC640 q T7...
  • Page 10 Construction 13. Terminal block 14. Fuseholder + Fuse connectors F... q F1 : 4A (slow) q SK1 : CH1 (2p) q SK2 : CH2 (2p) q SK3 : CH3 (2p) 15. IC , Check the q SK4 : CH4 (2p) q SK5 : CH5 (2p) position of the notch ! q SK6 : CH6 (2p)
  • Page 11 Hook-up diagram 16. Hook-up diagram Cold-cathode fluorescent lamps Inspect the complete assembly once more before applying power to the unit !
  • Page 12 Connection 17. Use Connect this kit according to the wiring diagram. LED LD1 will light if the operating voltage is correct. Take all necessary precautions to avoid electroshocks when connecting cold-cathode fluorescent lamps : the inverter ‘FLPS1’ uses a potentially life-threatening voltage. This kit is available in various countries.
  • Page 13 18. PCB layout.
  • Page 16 VELLEMAN Components NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be www.velleman-kit.com Modifications and typographical errors reserved © Velleman Components nv. H8044IP - 2002 - ED1...