Related Manuals for Bissell 6100 Series
Summary of Contents for Bissell 6100 Series
- Page 1 U S E R ’ S G U I D E 6100 SERIES 220-240V Safety Instructions Product View Assembly 6-9 Operation 10-15 Maintenance and Care 16-17 Troubleshooting 18 Consumer Services 19 Replacement Parts 20 Warranty...
- Page 2 Consumer Services department, so, should you ever have a question, you’ll receive fast, considerate assistance. My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a global leader in the design, manufacture, and service of high quality homecare products like your Healthy Home Vacuum.
-
Page 3: Important Safety Instructions
10 amp (AsTA approved to Bs 1362) fuse is fitted in the carrier contained in the plug. (spares may be obtained from your BIssell supplier). If for any reason the plug is cut off, it must be disposed of, as it is an electric shock hazard should it be inserted into a mains socket. -
Page 4: Product View
roduct view Upper Handle TurboBrush ™ Screen EasyEmpty™ Dirt Container Headlight Height Adjustment Dial Furniture Protection Guard Brush w w w . b i s s e l l . c o m Power Switch Hose Release Button Carrying Handle Brush Switch Filter Door Latch HEPA Filter... - Page 5 Place crevice tool inside telescoping wand. Store tools on vacuum as shown. w w w . b i s s e l l . c o m caUtIon: Do not plug in your vacuum cleaner until you are familiar with all instructions and operating procedures.
-
Page 6: Operation
Handle positions Use your foot to pull the handle release pedal back to recline the vacuum cleaner. Height adjustment there are seven height settings available for various floor surfaces. turn the dial on the foot of the cleaner to the desired setting. -
Page 7: Using The Tools
peration Fingertip brush switch the rotating brush is turned on or off using the switch at the side of the top of the handle. the brush will start rotating when the unit is reclined. the brush should be on for most carpeted floors. you may want to turn the brush off for bare floor cleaning or other delicate surfaces. -
Page 8: Crevice Tool
peration TurboBrush Use rotating brush action for small areas such as stairs and upholstery. note: Press gently when using the turbobrush to gain maximum cleaning. too much pressure could cause the brush to stop rotating. Combination brush Use longer soft bristles for dusting. Remove long bristle portion and use shorter stiff bristles when agitation is needed to remove debris. -
Page 9: Emptying The Dirt Container
. b i s s e l l . c o m caUtIon: Make sure vacuum cleaner has been switched off and unplugged before removing dirt container. -
Page 10: Cleaning The Foam Filter
aintenance and care Cleaning the dirt container additional steps can be taken to clean the dirt container as necessary. Ensure the dirt container has been emptied. Remove the lower portion by pressing the front and back latches on the upper portion as shown. -
Page 11: Maintenance And Care
HEPa System, you must ™ use the bISSEll HEPa filter cartridge. To remove the HEPA filter cartridge, push down on the filter door latch and pull door away from the cleaner. Lift the tab at the top of the HEPA filter cartridge and pull cartridge away from the cleaner. -
Page 12: Clearing Clogs
If you notice a change in the sound of the motor or a reduction in the spinning action in the dirt container, check for a clog. -
Page 13: Thermal Motor Protection
aintenance and care clearing clogs continued If suction is normal at the hose, follow these steps to check for and clear the clog for floor cleaning: Check diverter area at back of machine for diverter position and clogs. When the hose wand is inserted in the base, the diverter should be down. -
Page 14: Brush Maintenance
aintenance and care Brush reset If something becomes lodged in the foot and the brush shuts off, turn the cleaner off and unplug from the electrical outlet. Remove the obstruction. the brush will automatically reset when the cleaner is plugged in and turned back on. -
Page 15: Changing The Light Bulb
aintenance and care Changing the light bulb Unplug cleaner from electrical outlet. Recline handle for easier access to light bulb and remove screw to lift off lens. Remove the bulb by grasping bulb and pulling straight out of the socket. Install the new bulb by pushing gently into the socket until the bulb snaps into place. -
Page 16: Troubleshooting
Vacuum is in upright position Brush is jammed Brush needs to be reset Handle not fully attached Vacuum cleaner won’t pick up or low suction Possible causes Incorrect height setting Hose wand not properly positioned Dirt container not installed properly... -
Page 17: Please Do Not Return This Product To The Store
Hole or crack in hose other maintenance or service not included in the manual should be performed by an thank you for selecting a bISSEll product. Please do not return this product to the store. w w w . b i s s e l l . c o m Remedies 1. - Page 18 If your bISSEll product should require service: In the UK, Australia or New Zealand, call BIssell Consumer services at the numbers below and we will give you the location of a BIssell Authorized service Center in your area. for all other countries, contact your local in country distributor for questions, service, or repair.
- Page 19 - BISSELL Healthy Home Vacuum™ below is a list of common replacement parts. While not all of these parts may have come with your specific model, they are available for purchase if desired. Please note, all attachments may not store on board your vacuum.
-
Page 20: Limited Two-Year Warranty
*eXCePTIoNs AND eXClUsIoNs identified below, BIssell homecare, Inc., will replace (with new or remanufactured components), at BIssell’s option, free of charge from the date of purchase by the original purchaser, for two years any defective or malfunctioning part do to manufacturers defect.