Advertisement
QUICK SETUP GUIDE
INTRODUCTION
Thank you for purchasing this Legamaster e-Screen
Please refer to the user manual that can be found on
interactive display. This Quick Setup Guide will help
the USB drive for more detailed instructions and the
you setup the monitor and cover the basic operation
full safety and installation information.
instructions.
CAUTION
MOUNTING OF THIS PRODUCT CAN ONLY BE EXECUTED BY QUALIFIED STAFF
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL
SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD
FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
WARRANTY
Legamaster guarantees the repair or replacement,
If you wish to make a claim under the warranty or
free of charge, of faulty e-Screens and/or parts by an
you have any other service issues, please contact your
authorized service partner for a warranty period of 5
dealer or Legamaster directly. Please refer to www.
years. The warranty shall take effect on the date of
Legamaster.com/warranty for specific warranty infor-
purchase as stated on the receipt.
mation for your market.
RECYCLING INFORMATION
This product, when disposed of, is supposed to be
By disposing this product correctly you will help
collected and recycled according to your country's
ensure that the waste undergoes the necessary
legislation to reduce environmental burden.
treatment, recovery and recycling and thus prevent
When you dispose of this product, please contact a
potential negative effects on the environment and
distributor or an affiliate in your country. The contact
human health which could otherwise arise due to
addresses are listed on the Legamaster website
inappropriate waste handling.
http://www.legamaster.com.
COMPLIANCE
INCLUDED ACCESSORIES
FCC:
CE:
Item
FCC CFR Title 47
EN55032
IR Remote Control (Batteries Included)
part 15 Subpart B.
EN55024
Quick Setup-Guide
EN61000-3-2
CB:
EN61000-3-3
Power Cable
IEC62368-1
EN62368
HDMi Cable
USB Cable
VGA Cable
2 x High precision stylus
USB drive with user manual
LM-QSG-ETX-5510_GB.indd 5-8
Control pad table
Volume Up
Volume Down
Settings
Home
Back
Source
On/Off
17
16
CONNECTOR TABLE
IR receiver
16
USB 2.0
Ambient light sensor
+ status LED
17
USB 2.0
QUICK SETUP GUIDE
OPERATIONS
TURNING THE DISPLAY ON AND OFF
Turning the display on
Turning the display off
1.
Connect the display to an AC power outlet
With the Power on, press the power button on the control pad.
"|"
2.
Ensure the AC switch is set to
.
A warning message will appear. Alternatively you can use the
3.
Press the power button on the control pad, alternatively
power button on the remote control. To turn off power com-
you can use can use the power button on the remote
pletely, turn the AC switch to „O" or disconnect the AC power
control.
cord from the power outlet.
Note:
If there is no signal input for a period of time, the display will automatically go into power saving (sleep) mode.
ADJUSTING THE VOLUME AND INPUT SOURCE
Adjusting the Volume
2. Using the remote, press the SOURCE button and use the
1. Using the remote or control panel, press the VOLUME+ or
directional arrows to select the desired source.
VOLUME- to increase or decrease the volume.
3. If the display cannot find a source, a "No signal" message
will appear.
Selecting the input source
1. Press the SOURCE button on the control pad. The screen
will display available sources. Select a source by touching
the icon displayed on screen.
REMOTE CONTROL
Label
Description
Turn the display on and off
Back / return to previous menu
Navigational buttons
Select / confirm (when in menu) or Freeze screen
(when not navigating menu's)
Menu
Home
Source selection menu
Volume down
Mute
Volume Up
09.05.19 14:34
Advertisement
