Coast Spas TSPA-MP Quick Reference Card

TSPA-MP SPA PACK
The Quick Reference Card provides a quick overview of your spa's main
functions and the operations accessible with your digital control pad.

Starting Pump 1:

Press Pump 1 key to turn Pump 1 on at low speed. Press a second
time to turn pump to high speed. A third time turns pump off. A built-in
timer automatically turns pump off after 20 minutes, unless pump has
been manually deactivated first.
The "Pump 1" icon lights up when Pump 1 is on at high
speed. It flashes when pump is on at low speed.

Starting Pump 2:

Press Pump 2 key to turn Pump 2 on at low speed. Press a second
time to turn pump to high speed. A third time turns pump off. A built-in
timer automatically turns pump off after 20 minutes, unless pump has
been manually deactivated first.
The "Pump 2" icon lights up when Pump 2 is on at high
speed. It flashes when pump is on at low speed.

Turning the light on:

Press Light key to turn light on at high intensity. Pressing a second and a
third time reduces light intensity. A fourth time turns light off. A built-in
timer automatically turns light off after 2 hours, unless light has been
manually deactivated first.
Fiber Box Option: If your spa is equipped with an optional fiber box,
press Light key once to turn fiber box (motor & light) on. Press a
second time to turn fiber box motor off and leave light on. A third time
turns both fiber box motor & light off. A built-in timer automatically turns
fiber box off after 2 hours, unless fiber box has been manually deacti-
vated first.

Setting water temperature:

Use Warm or Cool arrow key to regulate water temperature. The
temperature setting will be displayed for 5 seconds to confirm your
new selection.
The "Set Point" icon indicates the desired temperature,
NOT the current water temperature!
Water temperature can be adjusted by 1-degree increments from
59 to 104˚F (15 to 40˚C).

Economy mode:

Press Econo. key to override the Economy mode programming (see
overleaf). The override will last until midnight.
The "Economy Mode" icon lights up when the system is
in Economy mode.

Quiet mode:

Press Quiet key to turn down pumps and blower. Simply press key to
resume normal operations. The system will automatically return to
Normal mode after 1 hour, unless it has been reactivated.
The "Quiet Mode" icon lights up when the system is in
Quiet mode.

Temperature display:

The display toggles every 5 seconds alternately showing the hourly
time and the current water temperature.

Automatic water heater start:

When water temperature is 1˚F (0.5˚C) lower than the Set Point, the
heater will automatically turn on until water temperature reaches Set
Point plus 1˚F (0.5˚C).
The "Heater" icon lights up when the heater is on. It flashes
when there is a request for more heat but the heater has not
yet started.
TROUBLESHOOTING
Pumps have started up for one minute on several occasions and "Filter
Cycle" icon is flashing.
Not a bug but a feature!
Our Smart Winter Mode protects your system from the cold by
turning pumps on for one minute several times a day to prevent water
from freezing in pipes.

A service icon is displayed.

A problem has been detected.
Do not enter the water! Check and open water valves. Clean filters
if necessary. Check water level. Add water if needed.
Shut power off and power your spa up again to reset the system.
Call your dealer or service supplier if problem persists.
Water temperature is flashing.
Water temperature in the spa has reached 112˚F (44˚C).
Do not enter the water! Allow the water to cool down.
The system will reset itself when water reaches 109˚F (43˚C).
Call your dealer or service supplier if problem persists.
Filter cycle stops and "Filter Cycle" icon is flashing.
Not a bug but a feature!
To prevent excessive water temperature caused by too long filter
cycles, the system will cancel a filter cycle after 3 hours if water
temperature exceeds Set Point by more than 2˚F (1˚C).
40-minute filter cycle time-out.
If you turn a pump, blower or light on during a filter cycle, the cycle will
be interrupted and will only resume 40 minutes after you (or the
system) have turned the last active output off. The "Filter Cycle" icon will
flash.
The display is flashing.
A power failure has occurred. Press any key to reset the system,
then reprogram all desired parameters.
Quick Reference Card