Advertisement
Ensure the sander is turned off before removing scrap pieces from the table.
DO NOT operate the sander when you are tired, under the influence of alcohol, drugs or intoxicating medication.
3
DO NOT turn the sander on before the work table is clear of all objects, tools, wood scraps etc.
7
DO NOT use sander without the table. DO NOT leave sander running unattended, and DO NOT stand in side line of the abrasive disc.
7
DO NOT touch the abrasive disc whilst operating, or whilst sander is plugged into the mains power.
7
DO NOT switch the sander on while the workpiece is in contact with the abrasive.
7
DO NOT operate the sander if any parts are damaged or missing as this may cause failure or possible personal injury.
7
DO NOT allow children or untrained persons to operate the sander. Keep them away from the work area.
7
DO NOT use the sander for any purpose other than wood finishing.
7
DO NOT modify or change the sander motor with a different rating.
7
WARNING! DO NOT sand any materials containing asbestos.
7
When not in use unplug from the mains power supply and make every effort to ensure the sander is childproof.
p
3
2. TECHNICAL SPECIFICATION
Disc size . . . . . . . . . . . . . . .Ø305mm
Disc Speed . . . . . . . . . . . . .1450rpm
Table . . . . . . . . . . . . . . .156x438mm
3. ASSEMBLY
3.1.
Unpack the sander and check contents. If there are any damaged or missing parts contact
your supplier immediately.
Contents: • Sander Assembly • Table
3.2.
Upon receipt the lever handle assembly (fig1.3) and/or guide screw (1) may be
screwed into bass assembly at point (X), or may be located in a plastic bag.
If screwed into bass (point X), remove and fit table (A) in position and secure
by inserting handle and screw (1 & 3).
Note: when handle section of lever (3) is pulled (against the internal handle spring)
towards the screw head (4) the locking screw (2) is then free to turn. The table
may be set at any angle between 0 ±45
1.6mm clearance between table and the face of the sanding disc,
see figure 1. Lock the table both sides by tightening lever (3).
3.3.
If dust extraction system is available connect to extraction point.
3.4.
The mitre gauge, when required, locates in the table groove.
3.5.
Before use, the sander must be positioned on a stable, fireproof
bench or table which is strong enough to take the weight of the
machine and the workpiece. Although the sander is supplied with
rubber feet it should also be bolted to the work surface.
WARNING! Failure to comply with this instruction could result in damage or severe personal injury.
p
4. OPERATING INSTRUCTIONS
4.1.
WARNING! Ensure that you have read, understood and apply the safety instructions in Section 1.
Ensure you wear approved safety goggles, gloves, ear defenders and, respiratory protection.
WARNING! Before each use rotate the sanding disc by hand to check it is undamaged and secure.
Remove adjusting keys and wrenches before turning the machine on.
p
WARNING! DO NOT switch the sander on whilst the workpiece is in contact with the disc. Keep any guards and holding screws in
place, tight and in good working order. A guard or other part that is damaged should be repaired/replaced before the sander is used.
p
4.2.
Table adjustment
The table is adjustable through 45
4.3.
Mitre gauge adjustment
The gauge is adjustable through ±45
4. OPERATING INSTRUCTIONS
5. MAINTENANCE
The sander is maintenance free and only requires regular cleaning using a vacuum cleaner and dry brush.
BENCH TOP DISC SANDER
Model SM31/C
73/23/EEC Low Voltage Directive (S.I. 1994/3260)
89/336/EEC EMC Directive (S.I. 1992/2372)
98/37/EC Machinery Directive (S.I. 1992/3073)
93/68/EEC CE Marking Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required
for any claim. INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Table Tilt . . . . . . . . . . . . . . . . . . .60
Dust Extraction Point . . . . . .Ø52mm
• Mitre Gauge
, but, always ensure there is
O
by slackening the two lever locks (fig 1.3).
O
by slackening the thumb screw.
O
Declaration of Conformity
in conformity with the following standards and directives
The construction file for this product is held by the Manufacturer and may be inspected by a national authority
upon request to Jack Sealey Ltd.
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
O
• Hex. Key
We, the sole importer into the UK, declare that the product listed here
Signed by Mark Sweetman
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery Ltd.
01284 757500
01284 703534
Motor . . . . . . . . . . .230V 50Hz 750W
Weight . . . . . . . . . . . . . . . . . . . .28kg
fig 1
1st April 2000
E-mail: sales@sealey.co.uk
SM31C - 1056 - (1) - 010400
is
Advertisement
