Intended Use; Remaining Hazards; Unpacking And Checking Contents - Scheppach DP16SL Translation From The Original Instruction Manual

Avoid overloading the device
Operate the device only within the specified output
range. Do not use any low-powered machines for
heavy duty work. Do not use tools to perform work for
which they were not intended.
Maintain a steady foothold
Ensure that you maintain a steady foothold while
working. Avoid abnormal body positions and always
keep your balance.
Pull out the mains plug
Pull out the mains plug when not using the tool, prior
to maintenance, and when changing the drill bit.
Pull out the power plug.
Ensure that the mains connection is protected by at
least a 10 A-rated fuse.
Avoid unintentional start-up
Ensure that switch is turned off when plugging the
plug into the socket.
Keep an eye on your work
Always keep an eye on your machine and the object
you are working on. Never use the machine when you
are not concentrating or are distracted. Never use the
machine when you are under the influence of alcohol
or are taking medication.
Maximum workpiece size
Workpieces (max. 20 x 20 cm) may only be pro-
cessed if they can be clamped securely on the drill
table or in the vise.
Check the tool for damage
Before using the tool, safety devices and any slightly
damaged parts must be carefully checked to ensure
that they are in good working order. Visually examine
the tool's power cable on a regular basis. All parts
must be correctly assembled and meet all the con-
ditions required to ensure proper operation. Unless
otherwise specified in the operating instructions, any
damaged safety devices and parts must be properly
repaired or replaced by a professionally recognized
workshop. Never use tools with defective On/Off
switches.
Warning! Using any plug-in tools and accessories
other than those specified in these operating instruc-
tions can lead to injury. Now, please read and follow
all steps and procedures included in the operating
instructions.
m Intended use
This pillar drill is designed for drilling metal, plastic,
wood and similar materials. It is intended for use in
the private sector only.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Food and harmful materials may not be processed
with the equipment. The drill chuck is only designed
for use with drill bits and tools with a shaft diameter of
3 to 16 mm, and for cylindrical tool shanks. Tools with
a tapered shank can also be used. The equipment is
intended for use by adults only.
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufacturer
will be liable for any damage or injuries of any kind
caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial appli-
cations. Our warranty will be voided if the equipment
is used in commercial, trade or industrial businesses
or for equivalent purposes.
m Remaining hazards
The machine has been built using modern tech-
nology in accordance with recognized safety
rules. Some remaining hazards, however, may
still exist.
• Long hair and loose clothing can be hazardous
when the work piece is rotating. Wear personal
protective gear such as a hair net and tight fitting
work cothes.
• Wood chips and saw dust can be health hazard.
Be sure to wear personal protective gear such as
safety goggles and a dust mask. Use a vacuum ex-
haust system.
• Thrown work pieces can lead to injury if the work
piece is not properly secured or fed, such as work-
ing without a limit stop.
• The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
• Even when all safety measures are taken, some
remaining hazards which are not yet evident may
still be present.
• Remaining hazards can be minimised by follow-
ing the instructions in „safety precautions", „proper
use" and in the entire operating manual.

Unpacking and checking contents

WARNING: If any parts are missing, do not at-
tempt to assembly the drill press, plug in the
power cord, and turn the switchon until the miss-
ing parts are obtained and correctly installed.
Separate all parts from packaging material and check
each item ‚th the falling tables af „standard contents"
(Same parts are packed inside of the pulley cover).
Do not discard the packaging immediately, in case
you have to send this product back to your dealer.
GB 23