Advertisement
If
you need any assistance with or have any questions about the wiring or operation of your CMD-2000 remote system,
please call the Dakota Digital technical assistance line at (605) 332-6513 or email us at dakotasupport@dakotadigital.com.
TRANSMITTER PROGRAMMING
All of the transmitters to be programmed into the system should be available. This sequence will erase any previously
programmed transmitters. If a transmitter is lost or stolen, go through the programming sequence with the remaining transmitters
and the lost one will be erased. The programming light (LED) is located on the side opposite the antenna, next to the programming
switch.
1.
Press and release the programming switch 3 times. The LED should come on and remain on steady.
2.
Press button 1 on the first remote. The LED should go out and then come back on steady.
3.
Press button 1 on the second remote. The LED should go out and then come back on steady.
4.
Repeat this for up to 4 remotes total.
5.
When all of the remotes have been programmed in, wait for the LED to go out. The system will now operate normally with all
of the remotes.
BATTERY REPLACEMENT
Should the transmitter function become weak or erratic, the battery in the key chain transmitter may be weak. An indication of a
weak battery is that the red indicator may have a dim glow to it when either button is pressed. If this occurs, first check the system
by using the second transmitter provided. If the second transmitter functions properly, replace the battery in the defective
transmitter by the following method:
A.
Use a small, flat screw driver or knife to pry the case apart next to the chain.
B.
Carefully separate the two case halves.
C. Remove the battery noting the (+) and (-) position.
D. Replace the battery with a new 12 volt type GP23A battery which is available at most electronic stores (Radio Shack, etc.).
E.
Carefully replace the top cover snap it into place.
F.
Check transmitter function.
DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical consultation is available to help you work through any questions
or problems you may be having installing one of our products. Please read through the Troubleshooting Guide. There, you will find the solution to most problems.
Should you ever need to send the unit back for repairs, please call our technical support line, (605) 332-6513, to request a Return Merchandise Authorization
number. Package the product in a good quality box along with plenty of packing material. Ship the product by UPS or insured Parcel Post. Be sure to include the RMA
number on the package, and include a complete description of the problem with RMA number, your full name and address (street address preferred), and a telephone
number where you can be reached during the day. Any returns for warranty work must include a copy of the dated sales receipt from your place of purchase. Send no
money. We will bill you after repair.
DAKOTA DIGITAL warrants to the ORIGINAL PURCHASER of this product that should it, under normal use and condition, be proven defective in material or
workmanship for the lifetime of the original vehicle it was installed in, such defect(s) will be repaired or replaced at Dakota Digital's option.
This warranty does not cover nor extend to damage to the vehicle's systems, and does not cover diagnosis, removal or reinstallation of the product. This
Warranty does not apply to any product or part thereof which in the opinion of the Company has been damaged through alteration, improper installation, mishandling,
misuse, neglect, or accident. Dakota Digital assumes no responsibility for loss of time, vehicle use, owner inconvenience nor related expenses.
Dakota Digital will cover the return standard freight once the product has been evaluated for warranty consideration, however the incoming transportation is to be covered
by the owner.
This Warranty is in lieu of all other expressed warranties or liabilities. Any implied warranties, including any implied warranty of merchantability, shall be limited
to the duration of this written warranty. No person or representative is authorized to assume, for Dakota Digital, any liability other than expressed herein in connection with
the sale of this product.
WARNING: This product can expose you to chemicals including lead, which is known to the State of
California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov
TECHNICAL SUPPORT
wire harness
programming
switch
SERVICE AND REPAIR
Dakota Digital Limited Lifetime Warranty
LED
11
MAN# 650016:A
Advertisement
