Advertisement
SETTING THE CLOCK
The time is displayed using the 12 hour clock with
PM indicator (PM off = AM).
1. Turn the SET control to TIME SET.
2. Press HR 2 repeatedly or hold down on the button to
adjust the hours. Release HR 2 when you reach the correct
hour.
3. Press 1 MIN repeatedly or hold down on the button to
adjust the minutes.
Release 1 MIN when you reach the correct minute setting.
4. Turn the SET control to RUN.
RADIO
1. Press SLEEP/ RADIO ON once to switch on the radio.
™ Display shows the radio frequency of the last selected
waveband briefly before returning to the clock time. Your
preset station is also shown if you are listening to a preset.
2. Press BAND if you wish to change waveband.
3. Adjust the sound using VOLUME.
4. Press ALARM RESET/ RADIO OFF to switch off.
The set complies with the FCC-Rules, Part 15.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
RADIO
STORING AND USING PRESET STATIONS
You can store up to a total of 10 radio stations in the memory, 5
on each waveband.
1. Tune to your desired station (see TUNING TO RADIO STATIONS).
2. To store a preset, hold down briefly on a PRESET button 1-5
until you hear a double beep.
™ Display shows the preset number of your station.
3. Repeat steps 1 and 2 to store your other stations.
• You can overwrite a preset station by storing another
frequency in its place.
4. Press a PRESET button 1-5 to listen to a preset station.
All manuals and user guides at all-guides.com
RADIO
Automatic tuning
• Press HR 2 or 1 MIN one second or more to tune to your
station.
™ The radio automatically tunes to a station of sufficient
reception.
Manual tuning
• Press HR 2 or 1 MIN briefty and repeatedly until your
reach the desired frequency.
To improve reception:
FM:
Adjust the position of the power cord (built-in
antenna) for optimum reception.
AM:
Uses a built-in antenna inside the set. Direct the
antenna by adjusting the position of your set.
SETTING THE ALARM
GENERAL
Two different alarm times can be set. This can be useful when
you need to be woken up at a different time e.g. during the
week and at the weekend:
• ALARM 1 – radio mode
• ALARM 2 – buzzer mode . The gentle wake buzzer alarm
increases its beep tone frequency within seconds.
SETTING THE ALARM TIME AND MODE
1. Turn the SET control to ALARM 1 or ALARM 2.
™ Display shows the alarm time digits with the
or
indicators flashing.
2. Press HR 2 repeatedly or hold down on the button to adjust
the hours.
ReleaseHR 2 when you reach the correct hour.
3. Press 1 MIN repeatedly or hold down on the button to
adjust the minutes.
Release 1 MIN when you reach the correct minute setting.
4. Turn the SET control back to RUN.
5. While the radio is switched off, select your choice of alarm
mode by pressing ALARM 1-RADIO or ALARM 2-BUZZ.
™ Display shows
or
SETTING THE ALARM
Notes: If you have selected the ALARM 1 RADIO, make sure
you have properly tuned to a station before turning off
the set.
If you set and activate the same alarm time for both
alarms, only the ALARM 2-BUZZ will be activated at
the set time.
SWITCHING OFF THE ALARM
There are three ways of switching off the alarm. Unless you
cancel the alarm completely, the 24 hour alarm reset option
will be automatically selected after 59 minutes, from the time
your alarm time first goes off.
24 hour alarm reset
If you want the alarm mode to be stopped immediately but also
wish to retain the same alarm setting for the following day:
• Press ALARM RESET/ RADIO OFF.
™ You will hear a beep tone confirming 24 hour reset
activation.
SLEEP MODE
SETTING SLEEP
1. Press SLEEP/ RADIO ON to switch on the radio.
2. Within 1 second, press SLEEP/ RADIO ON again once or
more until the display shows
While in the SLEEP display, press SLEEP/ RADIO ON once or
more to select your sleep time.
™ Display shows in sequence:
period time options: SL:60, SL:30, SL:15 and OFF.
™ The sleep time and radio frequency appear briefly before
showing standby clock time with the
indicator, if SLEEP is activated.
3. To cancel sleep, press either:
• ALARM RESET/ RADIO OFF
• REPEAT ALARM/
• SLEEP/ RADIO ON once or more until
disappears from the display.
.
SL:60.
and
and the sleep
BRIGHTNESS CONTROL
Advertisement
