Related Manuals for Cloudray CR30C
Summary of Contents for Cloudray CR30C
- Page 1 南京晨锐腾晶激光科技有限公司 NANJING CRD LASER TECHNOLOGY CO., LTD CR30C Laser Operator’s Manual...
-
Page 2: Table Of Contents
The back panel Description…………………………………………………………………………….8,9 Series CR Parameters and Installation diagram CR Series laser parameter table………………………………………………………………………..10 CR30C Installation diagram……………………………………………………………………….…..10 Figure 1：The panel Description…………………………………………………………………….….11 Figure 2：CR30C Outline diagram……………………………………………………………… …… 12 Figure 3：CR30C Mounting hole…………………………………………………………………….…13 CRD Laser after-sales service commitment CRD Laser after-sales service commitment………………………………………………………... 14,15... -
Page 3: Dangerous Warning
Lasers emit invisible infrared laser radiation at the 10.6 µ m CO wavelength. Since direct or diffuse laser radiation can inflict severe corneal and skin injuries, always wear eye protection when in the same area as an exposed laser beam. CR30C Label Icon ① ②... -
Page 4: Safety Regulations
◆ Class 4 laser product, Invisible laser radiation, Avoid eye or skin exposure to direct or scattered radiation ◆ Laser Radiation Warning. ◆ Laser label. Model: CR30C; Serial Number: 309001；Production date: January 4th,2009 ◆ Anti-action label removed, damage cannot be maintained. -
Page 5: Getting Started
南京晨锐腾晶激光科技有限公司 NANJING CRD LASER TECHNOLOGY CO., LTD Getting Started Inspection the packaging: 1. Inspect all shipping containers for signs of damage, severe deformation and damp. 2. Inspect the integrity of the sealing tape. 3. Inspect the position of Laser in the box is correct after the unpacking (loose in the package of plastic bubble). -
Page 6: Operation
Choice and connection of Power: ◆ DC switching power chose by customer will be matched to the requirements CR30C lasers, Voltage is 48V, current should be not less than 12.5A. ◆ The diameter of connecting wire between DC power supplier and laser tube should be larger than 2.5mm... - Page 7 南京晨锐腾晶激光科技有限公司 NANJING CRD LASER TECHNOLOGY CO., LTD ◆ The external control signals of CR30C Laser are accessed through the back panel BNC connector of the laser. Pulse width modulation (PWM): CR30C Laser is controlled laser power by Pulse width modulation (PWM). The low voltage range should be 0 to 0.5V (laser off), the high voltage, ranges should be...
-
Page 8: The Back Panel Description
南京晨锐腾晶激光科技有限公司 NANJING CRD LASER TECHNOLOGY CO., LTD The back panel Description: The panel including (see Installation Figure 1): ● Power input terminals ● Switch ●Power indicator light(green light) ● Laser indicator light(green red) ●BNC connector(signal input) Specific steps are as follows: 1. -
Page 9: Series Cr Parameters And Installation Diagram
Power Stability <1.2 Model Quality 2±0.2mm Beam Waist Size <7mrad Beam Divergence >100：1 Horizontal Polarization 0-25kHz，0-100% Modulation 48VDC/10A Power Supply Air cooling/water cooling 4L/M Cooling 500W Heat Dissipation Air cooling 357×93×145/water cooling 357×93×95 Dimensions 20000Hours Life 2. CR30C Installation diagram... - Page 10 L A S E R L E D / G R E E N D C L E D / G R E E N 3 0 . 5 1 2 . 5 2 7 0 . 4 1 2 . 5 6 5 .
- Page 11 L A S E R L E D / G R E E N D C L E D / G R E E N 1 2 . 5 2 7 0 . 4 1 2 . 5 4 8 V D C + 4 8 V D C - 6 5 .
-
Page 12: Crd Laser After-Sales Service Commitment
南京晨锐腾晶激光科技有限公司 NANJING CRD LASER TECHNOLOGY CO., LTD CRD Laser after-sales service commitment Dear customers: Thank you for purchasing series CR lasers from Nanjing CRD Laser Technology Co., LTD, in order to relieve your worries; we will make our warranted services for you, as the following commitments: 1. - Page 13 南京晨锐腾晶激光科技有限公司 NANJING CRD LASER TECHNOLOGY CO., LTD Belongs to the following conditions, No matter whether the product is during the period of free warranty, are not within the free warranty: ■ The fault or the damage caused by without following manual request, wrongly install or use and so on.
Need help?
Do you have a question about the CR30C and is the answer not in the manual?
Questions and answers