Related Manuals for zihatec ArduiBox MKR Series
Summary of Contents for zihatec ArduiBox MKR Series
- Page 1 Construction manual ArduiBox MKR Rev B ArduiBox MKR Rev B construction manual Rev. Date Description 2018-05-15 First Release 2020-12-17 Changed tor new ArduiBox MKR 2.0 1 of 15...
- Page 2 Construction manual ArduiBox MKR Rev B Tools: a regulated soldering iron (25..40W) with small tip a wet sponge to clean the thin solder wire Side cutting pliers Needle nose pliers 2 of 15...
- Page 3 Construction manual ArduiBox MKR Rev B Medium cross slot screwdriver 3 of 15...
- Page 4 Construction manual ArduiBox MKR Rev B Parts Basic Version: 2pole terminal block 3pole terminal block 14pole centipede header cathode 14pole male header Schottky diode self-tapping screws SB260 (D2) 4 of 15...
- Page 5 Construction manual ArduiBox MKR Rev B Place and solder the centipede headers Please assemble the 4 female centipede headers as in the picture below: Place and Solder the male headers Please assemble the 2 straight male headers as in the picture below: 5 of 15...
- Page 6 Construction manual ArduiBox MKR Rev B Place and solder the diode D2 cathode Place and solder the terminal K9 We've to put the block into the proto plate. Make sure you place them so that the open ends are facing out as shown: 6 of 15...
- Page 7 Construction manual ArduiBox MKR Rev B Preparing of 3pole terminal blocks Find the terminal blocks, they're grey or blue and come in 3-pin shape. We'll need to slide two 3-pin blocks together: 6.) Place and solder 3pole terminal blocks We've to put the blocks into the proto plate. Make sure you place them so that the open ends are facing out as shown: 7 of 15...
- Page 8 Construction manual ArduiBox MKR Rev B 7.) Solder Jumper J3 (optional): Perform this step only if you really don't want to use the additional voltage regulator of the standard kit. If you want to use the USB socket of the Arduino MKR for powering this step is unnecessary also.
- Page 9 Construction manual ArduiBox MKR Rev B Additional parts of Standard Version: cathode inductor Schottky diode overvoltage limiting diode 100uH/2.0A SB260 P6KE36CA (L1) (D3) (D1) voltage regulator electrolytic capacitor electrolytic capacitor TL2576-5 100uF/63V 1000uF/16V (IC1) (C1) (C2) Reset Button S1 9 of 15...
- Page 10 Construction manual ArduiBox MKR Rev B Power supply circuit: 10 of 15...
- Page 11 Construction manual ArduiBox MKR Rev B Place and solder Diode D3 and D1 (cathode) Please Note: D1 has no polarity! Place and solder the electrolytic capacitors C1 and C2 (minus pole) (minus pole) 11 of 15...
- Page 12 Construction manual ArduiBox MKR Rev B 10.) Place and solder the inductor L1 11.) Place and solder the voltage regulator IC1 Note: Please take care that the jumper J3 is not be bridged! 12 of 15...
- Page 13 Construction manual ArduiBox MKR Rev B 12.) Place and solder reset switch SW1 13.) Test the voltage regulator 9 – 35V DC You have to measure a voltage between 4.9 – 5.1V! 13 of 15...
- Page 14 Construction manual ArduiBox MKR Rev B 14.) Mount the pcb into the bottom shell Recess in the lower shell 15.) Fix the pcb in the lower shell with the screws 14 of 15...
- Page 15 Construction manual ArduiBox MKR Rev B 16.) Mount the Arduino MKR & shields It's time to mount the Arduino MKR board and optional shields: 17.) Mount the top shell Finish! 15 of 15...