Related Manuals for zihatec RasPiBox Zero Lite
Summary of Contents for zihatec RasPiBox Zero Lite
- Page 1 Construction manual RasPiBox Zero Rev A RasPiBox Zero Lite Version 2.1 construction manual Rev. Date Description 02.09.16 First release 1 of 18...
- Page 2 Construction manual RasPiBox Zero Rev A Tools: agregulated soldering iron (25..40W) with small tip a wet sponge to clean the thin solder wire Side cutting pliers 2 of 18...
- Page 3 Construction manual RasPiBox Zero Rev A Needle nose pliers Medium cross slot screwdriver 3 of 18...
- Page 4 Construction manual RasPiBox Zero Rev A Parts Basic Version: 2pole terminal block 2x20pole female header din rail holders (K2, K6, K8) (K1) cathode self-tapping screws Schottky diode MBRS140 4 of 18...
- Page 5 Construction manual RasPiBox Zero Rev A Prepare the terminal blocks Find the terminal blocks, they're grey or blue and come in 2-pin shapes. We'll need to slide two 2-pin blocks together: 2.) Place and solder terminal blocks We've to put the blocks into the proto plate. Make sure you place them so that the open ends are facing out as shown: 5 of 18...
- Page 6 Construction manual RasPiBox Zero Rev A 3.) Assemble and solder the 40 pole socket We've to place and solder the 2x20 pin socket for the Raspberry Pi : 4.) Place and solder the schottky diode cathode 6 of 18...
- Page 7 Construction manual RasPiBox Zero Rev A Set the solder jumper (basic kit only) Attention: Please set this jumper in the basic version only! You can supply the PiZero with 5V DC directely from the terminal K2 now. Set the soldering jumper Perform the next steps only if you have the standard kit (includes the parts of the voltage regulator and USB socket).
- Page 8 Construction manual RasPiBox Zero Rev A Additional parts of Standard Version: capacitor 100nF Electrolytic capacitor Tantal capacitor 68uF (C13) 220uF/35V (C12) (C11) suppressor diode switching regulator IC Schottky diode SM6T39CA (code GP608) LM2675 MBRS140 (code pH21) (D3) (IC2) (D1) inductor 330uH USB-A socket (L1) (K3)
- Page 9 Construction manual RasPiBox Zero Rev A Power supply circuit: 9 of 18...
- Page 10 Construction manual RasPiBox Zero Rev A Placement: 10 of 18...
- Page 11 Construction manual RasPiBox Zero Rev A Assemble Diode D5 Pls Note: D5 has no polarity! Assemble the switching regulator IC (IC2) Pin 1 Pin 1 11 of 18...
- Page 12 Construction manual RasPiBox Zero Rev A 8.) Assemble the capacitor C13 9.) Assemble the schottky diode D1 cathode 12 of 18...
- Page 13 Construction manual RasPiBox Zero Rev A 10.) Assemble the tantal capacitor C12 13 of 18...
- Page 14 Construction manual RasPiBox Zero Rev A 11.) Prepare the inductance and pads Depending from the situation on the market we equip the kits with different inductors. Some of them need a special preparation. preparation needed: no preparation needed: 11.1) add solder to the coil: 11.2) add solder to the pcb: 14 of 18...
- Page 15 Construction manual RasPiBox Zero Rev A 12.) Assemble the inductance L1 13.) Assemble the electrolytic capacitor C11 15 of 18...
- Page 16 Construction manual RasPiBox Zero Rev A 14.) Assemble the USB socket K3 (option) 15.) Connect the USB port It's very important that the wires for D+ and D- have exactely the same length. The optimal length for the cables is 6-7 cm. PiZero PP23 PP22...
- Page 17 Construction manual RasPiBox Zero Rev A 16.) Mount the pcb into the bottom shell 17.) Mount the 2 holders for the din rail Please take care to mount the holder from the inner channel to the outside! 17 of 18...
- Page 18 Construction manual RasPiBox Zero Rev A 18.) Mount the top shell! Milling on top side (sd card of PiZero) Finish! 18 of 18...