Sunbeam HL858A2-LT Instruction Manual page 5

POWER SUPPLY OPTIONS
This monitor is designed for operation with batteries or an AC / DC adapter. Use only a
compatible AC / DC adapter with required voltage and current as indicated in this manual.
Recommend Adapter Specification:
Model: FranMar International, FRM06-S05-UU
Rating:
Input: 100 - 240 V, 50 / 60Hz, 0.2A
Output: 5V, DC, 1A
Note:
1. No batteries are needed when operating with an AC / DC adapter. Please remove the
batteries if operating with an AC / DC adapter for an extended period. Leaving batteries
in the compartment may cause leakage and damage to the unit.
2. When you use the blood pressure monitor with AC/DC adapter, place the device where
you can easily reach and disconnect the adapter plug.
INSTALLING / REPLACING THE BATTERIES
1. Open the battery cover.
2. Insert 4 new AAA (1.5 V, LR03) alkaline batteries
into the compartment, as shown. Make sure the
polazrities "+" and "-" align with the symbols
inside the compartment.
3. Replace the batteries when:
• The low battery icon appears.
• The display is dim or does not turn on.
WARNING
• Do not mix new and used batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (cadmium) batteries.
• Such action may shorten the battery life or cause device malfunction.
• Batteries are hazardous waste. Do not dispose of them with household garbage.
Discard in accordance with local recycling guidelines.
• Choking hazard: keep batteries out of reach and away from children and pets.
• To prolong battery life and prevent damage caused by leakage, remove batteries if
the device will not be used for an extended period.
• Stored memory (if any) will not be deleted during battery replacement.
• Date and time must be reset if the AC / DC adapter is unplugged and the unit is
without batteries. Even with batteries in the monitor, plugging the AC adapter into
the monitor causes the time and date to reset.
• After replacing the batteries, reset the date and time.
8
SETTING THE DATE & TIME
1. Press START / STOP to turn on the monitor. The device will enter
STANDBY MODE.
2. While in standby mode, press + button for 3 seconds to enter
SETTING MODE. You may then adjust the current year / month / day
(1 - 31) / hour / minute.
3. Press the M button to advance each number. Press the + button to
save each selection. The YEAR digits flash first. Press the M button
to advance the numbers to the current year. If you advance too far,
continue pressing M to cycle back to the beginning. Tip: Press and
hold the M button to advance the digits more quickly.
4. Repeat the above steps to set month, day, hour and minute.
SELECTING USER ID
While in STANDBY MODE, press the + button to select
User 1 or 2.
VOICE BROADCAST ON / OFF
The Voice Broadcast feature announces test results out loud.
To turn the function ON or OFF:
1. While in STANDBY MODE, press + button for 3 seconds.
2. After confirming date and time settings, press M button to turn Voice Broadcast ON
or OFF.
Talking function is ON
ATTACHING THE CUFF
1. Remove all jewelry, such as watches and bracelets, from your left arm.
Note: If your doctor has diagnosed you with poor circulation in your left arm, use your
right arm.
2. Wrap the cuff on a bare arm or over thin clothing. Roll or slide up your sleeve to expose
the skin.
Note: Make sure the sleeve is not too tight. Thick clothing or a tightly-rolled sleeve will
cause inaccurate blood pressure measurements.
3. Slide the end of the cuff furthest from the tube through the metal ring to form a loop.
The smooth cloth should be on the inside of the cuff.
4. Hold your arm with palm facing up and slide the cuff loop onto your upper arm.
Position the tube off-center toward the inner side of arm in line with the little finger
OR
Press M button
Talking function is OFF
9