Hotpoint H3D91WBUK Quick Manual

Hotpoint H3D91WBUK Quick Manual

Advertisement

Quick Links

Quick guide
THANK YOU FOR BUYING A HOTPOINT PRODUCT.
In order to receive a more complete assistance, please
register your product on www.hotpoint.eu/register

CONTROL PANEL

ON/OFF Button (hold to Reset)
1
Programme Selection Knob
2
Start/Pause
3
Options Buttons
Crease Care
4
Dryness Level
5
Start Delay
6
Timed Drying
7
Cycle End Signal
8
Gentle (hold for Key Lock)
9
Rapid (hold to Mute)
10

INDICATORS

Dryness Level:
Iron Dry -
Programme Status:
Drying -
Empty water tank
-
Refer to the troubleshooting section:

FIRST TIME USE

Remove all the tapes used to hold items on the machine.
Before you use it, clean the inside of the drum to remove any
dust that could have accumulated during transport. Slight odour
or vapour may be found if you open the door during its first use,
this is normal and should only last a few minutes.
Make sure that the water tank is correctly inserted. Make sure
that the drain hose on the back of the dryer is properly
connected, either to the dryers's water tank or to your domestic
drainage system.
The dryer must be installed in a room with a temperature
ranging between 5°C and 35°C to ensure proper operation.

DAILY USE

Doing this will keep your machine working at its BEST:
- remember to empty your water tank after each drying cycle.
-
remember to clean your condenser unit regularly
(monthly).
- remember to clean your filter after each drying cycle.
Refer to the Care & Maintenance section.
1. Plug the dryer into the power supply socket.
2. Open the door and load garments; always refer to instructions on
clothing labels and the max loads indicated in the programme
section. Empty pockets. Make sure garments do not get caught
between the door and/or the door filter. Do not load items that
are dripping wet. Do not tumble dry large, very bulky items.
3. Close the door.
4. Press the "On/Off" button.
5. Select the most suitable programme
load.
6. Select the options, if necessary.
7. Press the
"Start/Pause"
button to begin drying.
8. At the end of the drying cycle, a buzzer will beep. An indicator on
the control panel signals the end of the cycle. Pull the load out
immediately to prevent the formation of creases on laundry.
9. Turn the machine off by pressing the "On/Off" button, open the
door and pull the clothing out. If the machine is not switched off
Policies, standard documentation, ordering of spare parts and additional product information can be
manually, after about a quarter of an hour from the end of the
found by:
cycle , the appliance turns off automatically to save energy.
• Visiting our website docs.hotpoint.eu and parts-selfservice.whirlpool.com
Note that some programme/option accords with "Crease Care"
• Using QR Code
system. This means that for some hours, after the end of the
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
drying cycle, the drum rotates at regular intervals to prevent the
contacting our After-sales Service, please state the codes provided on your product's identifi cation plate.
formation of creases.
In case of power failure, it is necessary to press the "Start/Pause"
button to restart the cycle.
2
Hanger Dry -
Cupboard Dry -
Cool Down - END End of Cycle
Clean door filter -
Clean the condenser unit
Failure:
Call after sales service.
for the type of fabric in that
Before using the appliance carefully read the Safety
Instructions.
END
END
h
h h
5
6
Extra Dry

OPENING THE DOOR DURING THE CYCLE

Laundry can be checked while the drying cycle runs and any
garments already dry can be removed, while drying continues for
the remaining items. After closing the door, press the "Start/Pause"
button to resume machine operation.

TRANSPORT AND HANDLING

Never lift the dryer by holding on to its top side.
1. Unplug the dryer
2. Remove the water from the water tank completely.
3. Make sure that door and water tank are properly closed.
4. If the drain hose is connected to your drainage system, re-connect
it to the back of the dryer (see "Installation" section in the Safety
Instructions).

CARE LABEL

Always check the care labels, especially when placing garments
in the tumble dryer for the fi rst time. Below are the most
commonly used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
10
9
7
8
EN
1
4
3
xxxx
xxxxxxxxxxxx

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the H3D91WBUK and is the answer not in the manual?

Questions and answers

Summary of Contents for Hotpoint H3D91WBUK

  • Page 1 Quick guide THANK YOU FOR BUYING A HOTPOINT PRODUCT. In order to receive a more complete assistance, please Before using the appliance carefully read the Safety register your product on www.hotpoint.eu/register Instructions. CONTROL PANEL ON/OFF Button (hold to Reset) Programme Selection Knob...
  • Page 2 OPTIONS PROGRAMS These buttons allow you to personalise the selected programme The duration of these programs will depend on the size of the according to personal requirements. load, types of textiles, the spin speed used in your washer and Not all options are available for all programmes. Some options any extra options selected.
  • Page 3 Quick guide THANK YOU FOR BUYING A HOTPOINT PRODUCT. CARE AND MAINTENANCE Cleaning the tumble dryer THANK YOU FOR BUYING A WHIRLPOOL PRODUCT. In order to receive a more complete assistance, please In order to receive a more complete assistance, please Before using the appliance carefully read the Safety •...
  • Page 4 Quick guide THANK YOU FOR BUYING A HOTPOINT PRODUCT. In order to receive a more complete assistance, please Before using the appliance carefully read the Safety register your product on www.hotpoint.eu/register TROUBLESHOOTING Instructions. Before contacting the After-sales Service, refer to the table below. Often the malfunctions are minor and can be solved in a few minutes.

This manual is also suitable for:

H3d91buk

Table of Contents