Page 1
USER’S MANUAL A42W64AT4 Thank you very much for choosing the Envision Series Plasma TV. We recommend that you take a few minutes to read carefully through this manual before installing and using the TV.
IMPORTANT SAFETY INSTRUCTIONS ..1 Precautions and Reminders……………………………………………………………………………..2 Features and Function………………………………………………………….…………………….….4 Front Panel Control……………………………………………………………………………………….5 Basic Installation…………………………………………………………………………………………..6 Connection to other equipment………………………………………………………………………….7 Remote Control Function ..9 OSD Menu Descriptions Main Menu ..…10 Setup Menu ..…10 Video Menu..11 Audio Menu……………………………………………………………………………………….…11 Feature Menu ...…...….12 EPG……………………………………………………………………………………………….….13 TVChannel ……………………………………………………………………..………………..….13...
IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment Read and follow all instructions. Do not operate this apparatus near water. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not block any of the ventilation openings.
Precautions and Reminders Do not place unit on uneven surfaces. Unplug immediately if there is any malfunction, like no video, no audio, smoke or a bad odor. Do not throw any object like metals or flammable materials into the TV set. Do not place the TV in confined spaces or in a box when using it.
Page 5
Precautions and Reminders DO NOT use liquid cleansers or aerosol cleansers to clean the plasma display. Dilute a neutral detergent with water and wipe with a soft cloth or gently clean with some absorbent cotton. Remember to unplug the AC mains cord before cleaning the display.
Features and Function 42 inch(107cm)Large Screen Flat Panel Plasma Display Panel Resolution: WVGA 852 x 480 Pixels MAX Brightness of Panel: 1500 Cd/m MAX Contrast Ratio of Panel: 10000:1 View Angle: Greater than 160° Internal TV Tuner, Air:69 channels Cable:135 channels Frequency Range:55.25MHz to 859.25MHz ATSC receiver, MPEG-2 decoder NTSC receiver, Video decoder...
⑦ ⑥ ⑤ ④ ③ ② ① ① MODE Mode: Press to select input signal modes or use as Enter in Menu operation. ② MENU Menu: Press to enter Menu or exit Menu. Left: Press to decrease the sound volume level or move Left in Menu operation. ③...
1. Connect TV Cable and Power Cord to this PDP TV Set. 2. Plug Power Cord to your home power outlet. 3. Check front panel LED for proper power connection: Blue color indicates this TV set is powered on; Red color indicates this TV set is in standby state. 4.
Connection to other equipment Please connect this TV Set to other equipment as picture below. You may have many types of equipment as: DVD, VCD, VCR, Set Top Box, X-Box and so on. (View from back of the TV set,left to right) INPUT CONNECTION OF VIDEO SIGNAL(DVD/VCD/VCR) s-video AV1-INPUT...
Page 10
Connection to other equipment INPUT CONNECTION OF PC SIGNAL(PC/DVD) Notice: If you see that display abnormality in screen, you need to check the cable connection and DVD setup. 24PIN DVI R/L INPUT ● D-SUB 15 Pin: Connect D-SUB signal cable (VGA cable) from PC to D-SUB jack at the back of this display. And connect the earphone cable from PC earphone output jack to AUDIO input jack near to the D-SUB jack.
Remote Control Function “Wide Mode” Normal, Zoom ,Wide, Cinema display select “EPG” Display the state, source “TV” TV source select, into TV state “SLEEP ” Select timer into power down state. off→30→60→90→off “CC” To select close caption options (CC1,CC2……) “ENTER ” To enter sub Menu or sub item .
OSD Menu Descriptions Main Menu 1. Press “MENU” key on remote control or front panel controls to bring up Main Menu. 2. Press “ ” or “ ” to move the cursor up and down the sub menu list. 3. Press “ ” or “ ” to select sub menu item.
Video Menu 1. Press “ ” or “ ” to move the cursor up or down the sub-item list. 2. Press "Enter" to enter the highlighted sub-item menu. 3. Press “ ” or “ ” to adjust the value of the sub-item. 4.
OSD Menu Descriptions Feature Menu 1. Press “ ” or “ ” to move the cursor up or down the sub-item list. 2. Press "Enter" to enter the highlighted sub-item menu. 3. Press “ ” or “ ” to adjust the value of the sub-item.
OSD Menu Descriptions Closed Captions section 1. Press “CC” key on remote control to select closed captions mode. NTSC TV: Off..CC1 ..CC2 .. ATSC TV: Off ..CS1 ..CS2.. 2. Select desired closed caption mode. 3.Closed captioning for analog NTSC channels is transmitted as CC1/CC2/CC3/CC4.Closed captioning for digital channels is transmitted as CS1/CS2/CS3...
Item Screen size Aspect Display pixels Panel Effective display size Spec Number of color Contrast Ratio Peak brightness TV Tuning Sound system TV Mode Color system AV1 ( S_Video/Video) AV2 ( S_Video/Video) Video Mode AV3 / AV4 COMPONENT X 2 (Y Cb Cr/Y Pb Pr) Signal input Plug and play...
Symptoms Picture freezes in antenna mode. The TV does not react to remote controller commands. Picture breaks up in DVI mode, especially when a set top box is connected. The picture is jerky or is corrupted (multiple small square boxes seen) in ATSC mode. Some channels are missing / are not found.
Page 18
Some parts of the screen do not light up After-images appear DTV signal jumps from 0 to 100 and back. No closed captioning seen when the TV is connected to a set top box. Troubleshooting The plasma TV panel is manufactured using an extremely high level of precision technology, however, sometimes some parts of the screen may be missing picture elements or have luminous spots.
Page 19
Envision Peripherals Inc. 47490 Seabridge Dr. Fremont, CA 94538 www.AOCdisplay.com Tech Support: 1-888-662-9888...