Advertisement
Quick Links
John Lewis
OXFORD Unit 1x2
Stock number: 83501
Thank you for purchasing this Oxford Unit 1x2. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product
Necessary Tools
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the retailer from whom
you bought this product.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
Read this leaflet in full before commencing assembly.
1
20598 - 1
1
Advertisement
Related Manuals for John Lewis OXFORD 83501
Summary of Contents for John Lewis OXFORD 83501
- Page 1 John Lewis OXFORD Unit 1x2 Stock number: 83501 Thank you for purchasing this Oxford Unit 1x2. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Pre-assembly preparation Please ensure instructions are read in full before attempting to assemble this product Necessary Tools Please check the pack contents before attempting to assemble this product.
- Page 2 Fittings and parts checklist RIGHT side panel x1 LEFT side panel x1 Fixed shelf x 1 Back panel x 1 Base x 1 Top x 1 Connecting bolts Angle x 1 x 12 Camlocks x 12 Screws 5x16 x 1 Dowels 8x35 x 18 Wall plug x 1 Plastic feet x 4...
- Page 3 Step by step assembly instructions Step One 1. Take the right side panel (1) and lay it on the clean and flat surface with the predriling holes uppermost. 2. Screw the four connecting bolts (A) into the holes provided. 3. Insert the three dowels (C) into the holes provided. ______________________________________________________________ Step Two 1.
- Page 4 ______________________________________________________________ Step Three 1. Take the base (5) and lay it on the clean and flat surface. 2. Insert the six dowels (C) into the holes provided. ______________________________________________________________ Step Four 1. Take the right side panel (1) and lay them on the clean and flat surface with the connecting bolt turned up.
- Page 5 _____________________________________________________________ Step Five 1. Locate the back panel (4) onto the right side panel (1) and base (5) as shown in the picture. 20598 - 1...
- Page 6 _____________________________________________________________ Step Six 2. Take the left side panel (2) and lay it on the clean and flat surface with the predrilling holes uppermost. 3. Screw the four connecting bolts (A) into the holes provided. 4. Insert the three dowels (C) into the holes provided. ____________________________________________________________ Step Seven 1.
- Page 7 _____________________________________________________________ Step Eight 1. Insert the four plastic feet (D) into the holes provided. 2. Attach the angle (F) using one screw (G) . Tighten the screw (G) using the crosshead screwdriver. _____________________________________________________________ Step Nine 1. Turn the carcase of the unit onto its plastic feet. 20598 - 1...
- Page 8 _____________________________________________________________ Step Ten 1. Take the top (6) and lay it on the clean and flat surface with the predriling holes uppermost. 2. Screw the four connecting bolts (A) into the holes provided. _____________________________________________________________ Step Eleven 1. Locate the top (6) onto the right side panel (1), and left side panel (2) as shown in the picture. 2.
- Page 9 _____________________________________________________________ Step Twelve 1. Insert the four plastic back holder (J) into the top (6) and base (5). 2. Tighten the four plastick back holder (J) using the crosshead screwdriver. _____________________________________________________________ Step Thirteen 1. Insert the eight cower caps (E) into the holes in the camlocks (B). The assembly is now complete.
- Page 10 Wall fixing - if in doubt seek professional advice Wood Brick or Masonry Cavity wall If fixing to wood Use an appropriate Special toggle make sure that it wall plug provided you wall plugs are isn’t chipboard as are sure your wall is needed.
-
Page 11: Care And Maintenance
Care and Maintenance Wood Furniture Wood displays different grain patterns depending on which way they cut - for example, the ‘medullary ray’ which can appear on oak furniture is a mark of good quality timber - these are just characteristics of the natural beauty of the wood.