Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec ZEROZON 200
Summary of Contents for Trotec ZEROZON 200
- Page 1 ZEROZON 200 ORIGINAL INSTRUCTIONS OXYGEN REGENERATOR...
-
Page 2: Table Of Contents
Information marked with this symbol indicates that the • Never insert any objects or limbs into the device. instructions must be observed. • Do not cover the device during operation. • Do not sit on the device. oxygen regenerator Zerozon 200... - Page 3 Trotec (Oz-One) or in a specialist shop. Wear an ozone respirator mask. • Insert the mains plug into a properly fused mains socket.
- Page 4 Without the air filter, the inside of the device will be heavily contaminated. This could reduce the performance and result in damage to the device. Note Do not use abrasive cleaners or solvents to clean the device. oxygen regenerator Zerozon 200...
-
Page 5: Information About The Device
The device is operated via a control panel at the device. The device can be used independently as well as in combination with an ozone generator from Trotec. The devices must be set up in the room at the same time. This way, the... -
Page 6: Transport And Storage
1. Open the cardboard box and take the device out. 2. Completely remove the packaging. 3. Fully unwind the power cable. Make sure that the power cable is not damaged and that you do not damage it during unwinding. oxygen regenerator Zerozon 200... - Page 7 • The room temperature should be approx. 5 °C higher than The stacking aid (1) allows a suitable ozone generator the usual room temperature. (e.g. Trotec Airozon 20000) to be stacked directly on Installation of the device in the room, the air of which is to the Zerozon 200.
-
Page 8: Operation
Switch-on / switch-off Man. button -starts the manual oxygen If possible, set up the device with a Trotec ozone generator in regeneration the room to be treated. The two devices can be connected and - illuminated when the device is in then started one after the other (see Use in combination with an... - Page 9 Please proceed as follows to start the device in combination You can choose between minutes, hours and seconds. Please with the Trotec ozone generator: proceed as follows to set the timer: 1. Seal off all openings of the room to be cleaned. It must be 1.
-
Page 10: Available Accessories
• Wait for 10 minutes before restarting the device. If the between device and energy source. device is not starting, have the electrics checked by a Shutdown specialist company or by Trotec. Warning The device is loud or vibrates: Risk of injury caused by ozone! •... -
Page 11: Maintenance
10. Date: ........11. Date: ........12. Date: ........Signature: ........ Signature: ......... Signature: ......... Signature: ......... 13. Date: ......... 14. Date: ........15. Date: ........16. Date: ........Signature: ........ Signature: ......... Signature: ......... Signature: ......... oxygen regenerator Zerozon 200... - Page 12 • increased noise level during operation of the fan • heavily contaminated air filter • dirty electrode (recognizable by: The hissing sound produced during ozone generation dies away.) oxygen regenerator Zerozon 200...
-
Page 13: Technical Annex
6. After inserting the filters, place the cover on the device and close it with the tension lock. Changing the filter(s) The filters must be replaced if they become soiled. After removing the filters, proceed as described in the chapter Assembly and start-up under Inserting filters. oxygen regenerator Zerozon 200... - Page 14 Wiring diagram oxygen regenerator Zerozon 200...
- Page 15 Item Designation Item Designation Screw (Liko cross recessed raised cheese head screw Inlet (Z-LO-200-inlet-01) DIN 7985 – M 5 x 8, black) Detent-edged washer (SKK5, Ø5.3 x Ø10 x 1.25) Front panel outlet (Z-LO-200-outlet-01) Basic housing(Z-LO-200-basic-housing-01) Filter (Z-LO-200-filter-01) oxygen regenerator Zerozon 200...
- Page 16 Detent-edged washer (SKK 4, Ø4.3 x Ø8.2 x 1.2<) screw, DIN 7985 – M 5 x 16) Rubber buffer (40 x 40 x M8 Type E, grey, non- Sealing plug (Ø19 x Ø16 x Ø11 x 1.5 x L8) colouring) Fan (K3G220RD2103) Basic housing (K-basic-housing, stainless steel, SBG-01879-04) Spring tension element (GN 831.1-110-NI Finger protection (K-finger-protection-02428-01) part 1/2) Handle (4245–L165mm; foldable) oxygen regenerator Zerozon 200...
- Page 17 Item Designation Item Designation Spring tension element (strike plate for lock part 2/2 Rivet (Ø4.8 x 8 Al) included in P10006576) Self-adhesive sealing tape (EPDM, Front panel – inlet (K front panel – inlet-02488-01) 10 x 2mm L=1320mm) oxygen regenerator Zerozon 200...
- Page 18 Allen screw (Liko DIN 7380 – M 4 x 10, black) Switch (SB53-N-2-16(6A)125/250VAC – green) Signal lamp (green LED) Cable bushing (M16 x 1.5 UL black) Switch (push button, flat, white, latching, illuminated) Lock nut (M16.5 x 1.5 UL black) Washer (DIN 125 – A Ø4.3) Cable tie mounts (screwable, 10.2x20.5, white) Relais (66.82.8.230.0000) Spigot (DN 197) oxygen regenerator Zerozon 200...
- Page 19 Note: The position numbers of the spare parts differ from those describing the positions of the components mentioned in these instructions. * not included in the scope of delivery Item Designation Item Designation Air filter 2 (296 x 296 x 48mm) Prefilter frame (K-frame Prefilter, stainless steel, SBG-01882-01) oxygen regenerator Zerozon 200...
-
Page 20: Disposal
The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment We – Trotec GmbH – declare in sole responsibility that the must not be disposed of with the household waste at the end of product designated below was developed, constructed and its life. - Page 21 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...