Page 1
All manuals and user guides at all-guides.com LCD-Monitor Chassis : LS23CFV Model : 2333HD SERVICE Manual TFT-LCD Monitor Contents 1. Precautions 2. Product specifications 3. Disassembly and Reassemble 4. Troubleshooting 5. Exploded View & Part List 6. Wiring Diagram 2333HD Refer to the service manual in the GSPN (see the rear cover) for the more information.
All manuals and user guides at all-guides.com 1. Precautions 1. Precautions 1-1. Safety Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
All manuals and user guides at all-guides.com 1. Precautions 1-2. Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual.
All manuals and user guides at all-guides.com 1. Precautions 1-4. Installation Precautions For safety reasons, more than two people are required for carrying the product. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock. Do not place the product in areas with poor ventilation such as a bookshelf or closet.
Page 7
All manuals and user guides at all-guides.com 1. Precautions Memo...
-The TV utilizes the HDMI system to implement perfect digital sound and picture quality. Specifications Item Description Model 2333HD LCD Panel TFT-LCD Panel, RGB Vertical stripe, normally White, 23-Inch viewable, 0.2655 (H) X 0.2655 (V) mm Pixel Pitch Scanning Frequency...
Page 9
All manuals and user guides at all-guides.com 2. Product specifications Specifications Item Description Model 2333HD Environmental Considerations Operating Temperature: 50˚C ~ 104˚F(10˚C ~ 40˚C) Operating Humidity : 10% ~ 80% Storage Temperature: -4˚C ~ 113˚C(-20˚C ~ 45˚C) Storage Humidity: 5% ~ 95% Antenna Input 75Ω...
All manuals and user guides at all-guides.com 2. Product specifications 2-2. Spec Comparison to the Old Models Model 2333HD(Refresh) 2333HD Design Screen Size 23” 23” Resolution 1920X1080 (FHD) 60Hz 1920X1080 (FHD) 60Hz Brightness 300cd/m2 300cd/m2 Contrast Ratio 1000:1 1000:1 Response Time Viewing Angle Left/Right/Up/Down : 80˚/80˚/80˚/80˚...
Description Ccde. No Remark Remote Control & BN59-00865A Batteries (AAA x 2) Power Cord 3903-000085 Stand Body BN96-07605D Samsung Electronics Service center Stand Base BN96-07604A D-Sub Cable BN39-00244G User’s Guide, Monitor Driver, BN59-00905A Natural Color Pro Software Cleaning Cloth BN63-1798B...
All manuals and user guides at all-guides.com 3. Disassembly and Assembly 3. Disassembly and Assembly This section describes the disassembly and reassembly sequences for this monitor. Warning: As this monitor has parts that are sensitive to static electricity, be careful when handling them. 3-1.
Page 13
All manuals and user guides at all-guides.com 3. Disassembly and Assembly Description Photo Screws 3. Insert a flat screwdriver into the groove and then lift up and remove the cover. 4. After remove COVER-REAR, then disconnect SPEAKER , FUNCTION wire. 5.
Page 14
All manuals and user guides at all-guides.com 3. Disassembly and Assembly Description Photo Screws 6. After disconnecting SHIELD-LAMP of left side, disassemble lamp wire between panel and IP Board. 7. Remove 4 screws of PC and DVI connector. Then, upset the shield. 8.
Page 15
All manuals and user guides at all-guides.com 3. Disassembly and Assembly Description Photo Screws 9. Remove the LCD panel. 10. Remove the WIRE-CONNECTOR from the LED PCB MODULE. 11. Remove the IR-PCB from the HOOK. 12. Remove the KNOB-CONTROL from the COVER- FRONT.
All manuals and user guides at all-guides.com 4. Troubleshooting 4. Troubleshooting 4-1. First Checklist for Troubleshooting Check the various cable connections first. - Check to see if there is a burnt or damaged cable. - Check to see if there is a disconnected cable connection or a connection is too loose. - Check to see if the cables are connected according to the connection diagram.
All manuals and user guides at all-guides.com 4. Troubleshooting 4-2. No Power Symptom Though the power swtich on, the LED power off and the screen is blank. Check Power cable. Check whether the Lamp connector is connected correctly to the IP. Major checkpoints Check whether the power cable is connected correctly to the MAIN.
Page 18
All manuals and user guides at all-guides.com 4. Troubleshooting 4-2-1. Circuit diagrams when the power does not turn on...
Does the digital data appear at the Check IC4010. output of RA4000, RA4001? Change a main PBA. Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace a lcd panel? Caution Make sure to disconnect the power before working on the IP board.
Page 20
All manuals and user guides at all-guides.com 4. Troubleshooting 4-3-1. Circuit diagrams and waveforms (Analog) when no screen is displayed on the monitor...
Page 21
All manuals and user guides at all-guides.com 4. Troubleshooting Analog PC 4-3-2. Waveforms when no screen is displayed ( ① R,G,B Output Signal of IC4010...
INPUT of IC4010 at RA4004, Change a main PBA. RA4005 (HDMI1) or RA4002, RA4003(HDMI2)? Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace lcd panel? Caution Make sure to disconnect the power before working on the IP board.
Page 23
All manuals and user guides at all-guides.com 4. Troubleshooting (Digital-HDMI) 4-4-1. Circuit diagrams and waveforms when no screen is displayed on the monitor...
Page 24
All manuals and user guides at all-guides.com 4. Troubleshooting Digital-HDMI 4-4-2. Waveforms when a blank screen is displayed ( ② Digital Output Data of IC4010 ③ Signal of HDMI(Data)
⑤ Does the digital data appear Change a main PCB ass’y. at R5055,R5056? Check a LVDS cable? Please, Call to Samsung Co. LTD. Replacea lcd panel? Caution Make sure to disconnect the power before working on the IP board. 4-10...
Page 26
All manuals and user guides at all-guides.com 4. Troubleshooting (Tuner_CVBS) 4-5-1. Circuit diagrams and waveforms when no screen is displayed on the monitor 4-11...
Page 27
All manuals and user guides at all-guides.com 4. Troubleshooting (Tuner_CVBS) 4-5-2. Waveforms when a blank screen is displayed ④ Tuner I2C Data signal. ⑤ Tuner_CVBS Output Signal 4-12...
④ Does the signal appear at check antenna cable Change a main PBA #16~25of TU5003? Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace lcd panel? Caution Make sure to disconnect the power before working on the IP board. 4-13...
Page 29
All manuals and user guides at all-guides.com 4. Troubleshooting (Tuner_DTV) 4-6-1. Circuit diagrams and waveforms when no screen is displayed on the monitor 4-14...
Page 30
All manuals and user guides at all-guides.com 4. Troubleshooting (Tuner_DTV) 4-6-2. Waveforms when a blank screen is displayed ④ Digital Channel DATA signal 4-15...
All manuals and user guides at all-guides.com 4. Troubleshooting 4-7. No Sound Symptom The LED power turns on but the screen is blank when the DVI cable is connected. Even though the LED power turns on, the screen is blank when connecting the DVI cable. Check the DVI cable connections.
Page 32
All manuals and user guides at all-guides.com 4. Troubleshooting (No Sound) 4-7-1. Circuit diagrams and waveforms when no screen is displayed on the monitor 4-17...
Page 33
All manuals and user guides at all-guides.com 4. Troubleshooting (No Sound) 4-7-1. Waveforms when a blank screen is displayed ⑥ The Signal are Inputed to IC9002 ⑦ DC 3.3V 4-18...
All manuals and user guides at all-guides.com 4. Troubleshooting 4-8. Faults and Corrective Actions Fault Photo Symptoms and Corrective Actions Remarks Symptoms: DVI signals are not recognized. * Refer to the Training Manual for information on inputting the DVI DDC. Causes: This fault occurs when the PC does not recognize the mode information because...
All manuals and user guides at all-guides.com 4. Troubleshooting 4-9. Adjustment 4-9-1. Service Instruction 1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. 2. Use the specified test equipment or its equivalent. 3.
All manuals and user guides at all-guides.com 4. Troubleshooting 4-11. Service Adjustment 4-11-1. White Balance - Calibration If picture color is wrong, do calibration first. Equipment : CA210, Patten : chess pattern Execute calibration in Factory Mode Source AV : PAL composite, Component : 1280*720/60Hz PC : 1024*768/60Hz (Gray patten) 4-11-2.
Page 37
All manuals and user guides at all-guides.com 4. Troubleshooting 4-11-4. Method of Adjustment 1. Adjust the white balance of AV, Component Modes. (AV→Component) a) Set the input to the mode in which the adjustment will be made. (RF→DTV→PC→DVI). * Input signal - VIDEO Mode : Model #2 (744*484 Mode), Pattern #16 - DTV,DVI Mode : Model #6 (1280*720 Mode), Pattern #16 - HDMI Mode: Model #6(1280*720 Mode), Pattern #16 b) Enter factory color control, confirm the data.
All manuals and user guides at all-guides.com 4. Troubleshooting 4-12. Software Upgrade 4-12-1. Micom Program Upgrade DDC Manager Connection PC for MCU upgrading Connect to Parallel port 1. Prepare PC to Upgrade the Program. 2. Prepare the DDC Manager 3.
Page 39
All manuals and user guides at all-guides.com 4. Troubleshooting Main MIcom Upgrade 1. Goto installed Program folder (winDDC_V2-39) 2. Run winDDC 3. Select WinISP Menu 4. Make same setting like picture. 5. Choose Flash memory type - CREAM-MFM(2333HD):WT61P8 4-24...
Page 40
All manuals and user guides at all-guides.com 4. Troubleshooting 6. Load File ( Select file to download) 7. Set Option to load Binary Files 8. Select files (bin file) 9. Click button to load files 10. Select “Flash1” and “Flash2” 4-25...
Page 41
All manuals and user guides at all-guides.com 4. Troubleshooting 11. Check the OK message (Load) 12. Click Auto Program button 13. If you see OK message (Verify), program download is completed After Upgrading Firmware Factory mode 1. Factory remote control (SET POWER ON ) INFO ->...
Page 42
1. Select WinISP Menu 2. Make same setting like picture. 3. Choose Device Type. - CREAM-MFM(2333HD):WT61P8 4. Load File ( Select file to download) 5. Set Option to load Binary Files 6. Select files (hex file) 7. Click button to load files...
Page 43
All manuals and user guides at all-guides.com 4. Troubleshooting 8. Check the OK message (Load) 9. Click Auto Program button 10. If you see OK message (Verify), program download is completed 4-28...
All manuals and user guides at all-guides.com 5. Exploded View & Part List 5. Exploded View & Part List 5-1. LS23CFVKF/XE - Exploded View...
Page 45
All manuals and user guides at all-guides.com 5. Exploded View & Part List 5-1-1. LS23CFVKF/XE - Parts List Location No. Code No. Description & Specification Q’ty SA/SNA Remark M0006 BN96-08779B ASSY SHIELD P-COVER;CREAM 23,SECC T0.8,( M0013 BN96-08777H ASSY COVER P-REAR;CREAM 23,EUROPE,ABS,PM M0027 BN96-08346A ASSY STAND P-BASE;LS24CM,ABS HB,BK23,H/G...
Page 46
All manuals and user guides at all-guides.com 5. Exploded View & Part List 5-2. LS23CFVKF/XE - Parts List Service Bom (SA: SERVICE AVAILABLE, SNA: SERVICE NOT AVAILABLE) Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark BN90-01846B ASSY COVER FRONT;LS23CF,EUROPE T0175 BN96-08732B ASSY SPEAKER P;16ohm,4pin,cream 23”,3W...
All manuals and user guides at all-guides.com 6. Wiring Diagram 6. Wiring Diagram 6-1. Wiring Diagram - Main Board...
Page 54
All manuals and user guides at all-guides.com 6. Wiring Diagram 6-2. Wiring Diagram - MAIN Board LVDS Connector (Connect to Panel) IP board 3708-001150 3711-005503 3701-001388 3701-001385 3701-001367 3722-000143 3701-001386 3722-002360 3722-002362 RGB Connector DVI-D Connector (PConnect to PC) (Connect to PC)
All manuals and user guides at all-guides.com 6. Wiring Diagram 6-3. Wiring Diagram - IP Board Power Lamp Connector Connector 9P (Connect with panel (Connect with inverter – left top of MAIN board) panel rear) Lamp Connector (Connect with panel inverter –...
All manuals and user guides at all-guides.com 6. Wiring Diagram 6-4. Connector Functions Connector Functions CN5002 Transmits LVDS signals from the Main board to the panel * When a problem occurs: The Blank Screen and No Power errors may occur. CN3000 VGA signal input terminal * When a problem occurs: The No RGB Output error may occur.