Advertisement
F
(XP-EV600D only)
Connecting a stereo
（僅XP-EV600D）
system (XP-EV600D only)
(F)
You can listen to CDs through a stereo system and record
CDs on a cassette tape and a MiniDisc. For details, see the
instruction manual that comes with the connected device.
Be sure to turn off all connected devices before making
connections.
Notes
• Before you play a CD, turn down the volume of the
connected device to avoid damaging the connected
speakers.
To OPTICAL OUT
• Us the AC power adaptor for recording. If you use the
至OPTICAL OUT
rechargeable bateries or dry batteries as a power source,
batteries may become completely depleted during
recording.
• Adjust the volume properly on the connected device so
Optical digital
that the sound will not be distorted.
connecting cord
光學數位連線
When recording a CD on a MiniDisc or
DAT
Make sure that the CD player is in pause before operating
the recording procedures.
About the E•A•S•S and SOUND function
when using the optical digital connect-
Stereo system, MiniDisc
ing cord
recorder, DAT deck, etc.
• To record high quality CD sound, set the E•A•S•S
立體聲系統、迷你光
switch to "1."
碟錄音機、DAT疊
• The SOUND function does not work on the the output
等。
sound from the OPTICAL OUT jack.
Precautions
On safety
English
• Should any solid objects or liquid fall into the CD
player, unplug it and have it checked by qualified
personnel before operating it any further.
• Do not put any foreign objects in the DC IN 4.5 V
Checking the remaining time on
(external power input) jack.
the CD and the number of tracks
On power sources
left (XP-EV600D only)
• When you are not using the CD player for a long time,
You can check the remaining time on the CD and the
disconnect all power sources from the CD player.
number of tracks left using DISPLAY on the remote
control.
On AC power adaptor
1
Press DISPLAY on the remote control.
• Use only the AC power adaptor supplied. Do not use
any other AC power adaptor. It may cause a
Each time you press the button, the display changes as
malfunction.
follows:
Display
Polarity of the plug
Normal play
Track number and
elapsed playing time
• Do not touch the AC power adaptor with wet hands.
Press DISPLAY once.
• Connect the AC power adaptor to an easily accessible
Track number and
AC outlet. Should you notice an abnormality in the AC
remaining time on the
power adaptor, disconnect it from the AC outlet
current track
immediately.
On rechargeable batteries and dry
Press DISPLAY once again.
batteries
The number of tracks
• Do not charge the dry batteries.
left and remaining time
• Do not throw the batteries into fire.
on the CD*
• Do not carry the batteries with coins or other metallic
objects. It can generate heat if the positive and negative
* Not displayed during single play or shuffle play.
terminals of the battery are accidentally contacted by a
metallic object.
To turn off the operation beep
• Do not mix rechargeable batteries with dry batteries.
• Do not mix new batteries with old ones.
sound
• Do not use different types of batteries together.
You can turn off the beep sound that is heard from your
• When the batteries are not to be used for a long time,
headphones/earphones when you operate your CD player.
remove them.
1
Remove the power source (AC power adaptor,
• If battery leakage occurs, wipe off any deposit in the
rechargeable batteries or dry batteries) from the CD
battery compartment, and install new batteries. In case
player.
the deposit adheres to you, wash it off thoroughly.
2
Connect the power source while pressing
Notes on the rechargeable batteries
s/OFF/CHARGE on the CD player or s on the
• To keep the original battery capacity for a long time,
remote control.
charge the batteries only when they are completely
depleted.
To turn on the beep sound
• If the battery is new or has not been used for a long
Remove the power source and then connect the power
time, it may not be charged completely until you charge
source without pressing s/OFF/CHARGE.
and discharge it several times.
• When carrying the rechargeable batteries, use the
Playing tracks in your
battery carrying case supplied with the rechargeable
batteries to prevent unexpected heat. If the rechargeable
favorite order (PGM play)
batteries and the metallic objects get contacted, heat or
fire may occur due to a short circuit.
You can program the CD player to play up to 24 tracks in
When to replace the rechargeable batteries
your favorite order.
If the battery life becomes shorter by about half, replace
1
During playback, press P-MODE/
repeatedly until
the batteries with new rechargeable batteries.
"PGM" appears.
2
On the CD player
Press r or t to select a track.
• Keep the lens on the CD player clean and do not touch
3
Press ca to enter the selected track.
it. If you do so, the lens may be damaged and the CD
"00" appears and the playing order increases
player will not operate properly.
by one.
• Do not put any heavy object on top of the CD player.
4
The CD player and the CD may be damaged.
Repeat steps 2 and 3 to select the tracks in your
• Do not leave the CD player in a location near heat
favorite order.
sources, or in a place subject to direct sunlight,
5
Press and hold ca until the PGM play starts.
excessive dust or sand, moisture, rain, mechanical
To check the program
shock, unleveled surface, or in a car with its windows
closed.
During programming, press ca repeatedly before step
• If the CD player causes interference to the radio or
5. Each time you press ca, the track number appears.
television reception, turn off the CD player or move it
Notes
away from the radio or television.
• Discs with non-standard shapes (e.g., heart, square, star)
• During the PGM play, you cannot check the program.
cannot be played on this CD player. Attempting to do so
• When you finish entering the 24th track in step 3, the
may damage the CD player. Do not use such discs.
first selected track appears in the display.
• If you select more than 24 tracks, the first selected
Note on moisture condensation
tracks are erased.
If the CD player is suddenly moved from a cold place to a
warm place, it may result in moisture condensation on the
pickup lens and malfunction or playback difficulties.
Should this occur, leave the CD player for a few hours,
then try playback again.
On headphones/earphones
Road safety
Do not use headphones/earphones while driving, cycling,
中文（繁體字）
or operating any motorized vehicle. It may create a traffic
hazard and is illegal in some areas. It can also be
potentially dangerous to play your headsets at high
volume while walking, especially at pedestrian crossings.
檢查CD的剩餘時間和剩餘曲目數（僅
You should exercise extreme caution or discontinue use in
XP-EV600D）
potentially hazardous situations.
可用遙控器上的DISPLAY來檢查CD的剩餘時
Preventing hearing damage
間和剩餘曲目數。
Avoid using headphones/earphones at high volume.
按遙控器上的DISPLAY。
1
Hearing experts advise against continuous, loud and
每按一次按鈕，如下所示地改變顯示：
extended play. If you experience a ringing in your ears,
reduce volume or discontinue use.
Consideration for others
一般顯示
Keep the volume at a moderate level. This will allow you
to hear outside sounds and to be considerate to the people
around you.
按１次DISPLAY
Maintenance
To clean the casing
Use a soft cloth slightly moistened in water or a mild
再按１次DISPLAY。
detergent solution. Do not use alcohol, benzine or thinner.
To clean the plugs
If the plugs become dirty, there is no sound or noise is
heard. Clean them with a dry soft cloth periodically.
*單曲播放或隨機播放時不顯示。
Troubleshooting
要關掉操作嗶聲時
Should any problem persist after you have made these
可以關掉操作C D 唱機時能從頭戴耳機／耳機
checks, consult your nearest Aiwa dealer.
聽到的嗶聲。
從C D 唱機上拆下電源（A C 電源轉接器、
"Hold" appears in the display when you
1
充電式電池或乾電池）。
press a button, and the CD does not
play.
2
邊按CD唱機上的s/OFF/CHARGE或遙控
➔The buttons are locked. Slide HOLD back.
器上的s，邊連接電源。
The CD player does not start charging.
要打開嗶聲時
➔During stop, press s/OFF/CHARGE.
拆下電源，然後連接電源，連接時不要按■/
➔For XP-EV600B and XP-EV600D, press s on the CD
OFF/CHARGE。
player, not s on the remote control.
The battery compartment lid is de-
按所需順序播放曲目
tached by an accidental drop, excessive
force, etc.
(PGM播放)
➔Attach it as illustrated below.
可以使C D 唱機按照所需順序，程式播放多至
24個曲目。
播放時反覆按P - M O D E /
1
「PGM」。
2
按r或t，選擇曲目。
按ca，輸入所選曲目。
3
出現「00」，並增加１個播放順序。
反覆步驟２和３，按所需順序選擇曲目。
4
按住ca，直至開始PGM播放。
5
Specifications
要檢查程式時
播放時，在步驟５之前反覆按 c a 。每按一
System
次ca，會出現曲目號。
Compact disc digital audio system
註
Laser diode properties
‧ PGM播放時，不能檢查程式。
Material: GaAlAs
‧ 在步驟３輸入完24個曲目時，會在顯示器上
Wavelength: λ = 780 nm
出現第１個選擇的曲目。
Emission duration: Continuous
Laser output: Less than 44.6 µW (This output is the value
‧ 如果選擇的曲目多於24個，則會拭除第１個
measured at a distance of 200 mm from the objective lens
選擇的曲目。
surface on the optical pick-up block with 7 mm aperture.)
Power requirements
For the area code of the model you purchased, check the
連接立體聲系統
upper left side of the bar code on the package.
（僅XP-EV600D）(F)
• Two LR6 (size AA) batteries: 3 V DC
• Two Ni-MH rechargeable batteries (size AA) (Sony
NH-7WMAA or equivalent): 2.4 V DC
可以透過立體聲系統收聽CD，並可將CD錄在
• AC power adaptor (DC IN 4.5 V jack):
磁帶和迷你光碟上。詳細說明，請參閱所連接
KR4 and E18 models: 100 – 240 V, 50/60 Hz
的裝置的使用說明書。連接前請務必關閉所有
TW2 model: 120 V, 60 Hz
連接的裝置。
CNA model: 220 V, 50 Hz
HK4 model: 230 V, 50/60 Hz
註
AU2 model: 240 V, 50 Hz
‧ 播放C D 前，請降低所連接的裝置的音量以
Dimensions (w/h/d) (without projecting
防損壞所連接的揚聲器。
parts and controls)
‧ 錄音時請使用A C 電源轉接器。若將充電式
Approx. 136 × 20.4 × 139 mm
電池或乾電池作為電源，則在錄音時電池可
能會完全耗盡。
Mass (excluding accessories)
‧ 請在所連接的裝置上適當調節音量，以使聲
Approx. 175 g
音不走音。
Operating temperature
將CD錄在迷你光碟或DAT上時
5°C – 35°C
在進行錄音操作前請務必確認C D 唱機處於暫
Design and specifications are subject to change without
停狀態。
notice.
有關使用光學數位連線時的E ‧ A ‧ S ‧ S和
SOUND功能
Supplied Accessories
‧ 要錄高質C D 音響時，請將E‧ A‧ S‧ S 開關設
XP-EV500:
Earphones (1)
為「1」。
AC power adaptor (1)
‧ SOUND功能對OPTICAL OUT插孔的輸出
XP-EV600B:
Earphones with remote control (1)
聲音無效。
AC power adaptor (1)
Rechargeable batteries (2)
Battery carrying case (1)
注意事項
XP-EV600D:
Earphones with LCD remote control (1)
AC popwer adaptor (1)
安全須知
Rechargeable batteries (2)
‧ 若有固體或液體掉進C D 唱機內時，請立即
Battery carrying case (1)
斷開電源並請有資格的人檢查後再繼續使
用。
‧ 請勿將任何異物塞入DC IN 4.5V（外接電
源輸入）插孔。
電源須知
‧ 長期不使用CD唱機時，請斷開所有電源。
AC電源轉接器須知
‧ 僅能使用附帶的A C 電源轉接器。請勿使用
其他任何類型的A C 電源轉接器，否則可能
會引起故障。
插頭極性
‧ 請勿用濕手觸摸AC電源轉接器。
‧ 請將AC電源轉接器連接到易於連接的AC電
源插座上。發現A C 電源轉接器不正常時，
請將其立即從AC電源插座上拔下。
充電式電池和乾電池須知
顯示器
‧ 請勿給乾電池充電。
曲目號和所經過的
‧ 請勿將電池扔入火中。
播放時間
‧ 請勿將電池和硬幣或其他金屬物品混在一起
攜帶。否則電池的正負極若被金屬物品相連
接，則會發熱。
曲目號和當前曲目
‧ 請勿混用充電式電池和乾電池。
‧ 請勿混用新舊電池。
的剩餘時間
‧ 請勿混用不同類型的電池。
‧ 長期不使用電池時，請將其取出。
‧ 電池漏液時，請擦去電池室內的漏液，並裝
入新電池。如果皮膚沾上漏液時，請將其徹
剩餘的曲目數和CD
底洗淨。
上的剩餘時間*
充電式電池須知
‧ 為長期保持充電式電池的原有容量，請僅在
完全耗盡時才給電池充電。
‧ 新的充電式電池或長期未使用的充電式電池
可能不能完全充滿電，須等充電使用數次之
後才能完全充滿電。
‧ 攜帶充電式電池時，請使用充電式電池附帶
的電池攜帶盒以防意外發熱。如果充電式電
池和金屬物品混合放置，則可能會因短路而
發熱或起火。
何時更換充電式電池
當電池使用時間縮短到約一半時，請更換新的
充電式電池。
CD唱機須知
‧ 請保持C D 唱機上的透鏡乾淨清潔，不要用
手觸摸。否則會損壞透鏡，C D 唱機不能正
常工作。
‧ 請勿在CD唱機上堆置重物，否則會壓壞CD
唱機和CD光碟。
‧ 請勿將C D 唱機放在熱源附近，或放在陽光
，直至出現
直接照射到的地方、或多塵多沙、潮濕、淋
到雨、有機械衝擊、不平坦的地方、或車窗
緊閉的汽車內。
‧ 如果C D 唱機影響收音機或電視機的接收，
請關掉CD唱機或將其移離收音機或電視機。
‧ 此C D 唱機不能用於播放形狀不規則（例如
心形、方形、星形）的光碟，否則會損壞
CD唱機。請勿使用該類光碟。
有關結露的說明
如果將C D 唱機從較冷的地方突然移到較暖和
的地方時，可能會在拾音透鏡上結露並發生故
障或造成播放困難。此時，請將C D 唱機擱置
幾個小時，然後再試著播放。
頭戴耳機/耳機須知
路上安全
開車、騎車或操作任何機動車輛時，請勿使用
頭戴耳機／耳機，否則可能有造成交通事故的
危險，而且在有些地區是違法的。行走時如果
用大音量收聽耳機也有潛在危險，特別是在橫
越馬路時。在有潛在危險的情況下，必須特別
注意或停止使用。
防止損傷聽覺
勿用大音量收聽頭戴耳機／耳機。聽覺專家建
議不要連續收聽、大音量收聽及持續收聽。若
感到耳鳴，請降低音量或停止使用。
顧及他人
請用適當的音量收聽，以便可聽到周圍的聲音
並且不會影響到周圍的人。
保養
要清潔外殼時
用稍微沾上一些水或中性清潔劑的軟布。請勿
用酒精、汽油或稀釋劑。
要清潔針形接點時
如果針形接點較髒，則會發不出聲音或有噪
聲。請周期性地用乾的軟布擦拭。
故障檢修
檢查過這些征候但仍不能解決問題時，請向附
近的愛華經銷店洽詢。
按下按鈕時在顯示器上出現
「Hold」，不播放CD。
➔按鈕被鎖定。請將HOLD滑回。
CD唱機不充電。
➔停止時，按s/OFF/CHARGE。
➔使用XP-EV600B和XP-EV600D時，請按
CD唱機上的s，而不是遙控器上的s。
電池室蓋因不小心掉下或施力過大而脫
開。
➔如下圖所示地裝上。
規格
系統
CD數位聲訊系統
雷射二極體特性
材料：GaAlAs
波長：λ＝780nm
發射持久性：連續
雷射輸出：小於44.6μW（此輸出值是在距離
7mm光圈的光學拾音元件的物鏡鏡面200mm
處測得的。）
電源
有關您購買的型號的區域碼，請參看包裝上的
條形碼的左上角。
‧ ２節LR6（AA）電池：3 V DC
‧ ２節鎳金屬氫充電式電池（A A ）（S o n y
NH-7WMAA或同等產品）：2.4 V DC
‧ AC電源轉接器（DC IN 4.5V插孔）：
KR4和E18型號：100∼240 V，50/60 Hz
TW2型號：120V，60Hz
CNA型號：220V，50Hz
HK4型號：230V，50/60Hz
AU2型號：240V，50Hz
D尺寸（寬／高／深）（不包括突起部
分和控制器）
約136×20.4×139mm
質量（不包括附件）
約175g
工作溫度
５℃∼35℃
設計和規格若有變更，恕不另行通告。
附帶附件
XP-EV500 ： 耳機(1)
AC電源轉接器(1)
XP-EV600B： 附遙控器的耳機(1)
AC電源轉接器(1)
充電式電池(2)
電池攜帶盒(1)
XP-EV600D： 附LCD遙控器的耳機(1)
AC電源轉接器(1)
充電式電池(2)
電池攜帶盒(1)
Advertisement
