Advertisement
Quick Links
COMPLETE INSTRUCTIONS FOR THE
LEE LOAD
CASE SLIDER · TR2449
FEED CRANK · LM3259
INDEXER · LM3243
INDEXER FLIPPER · LM3244
TURRET LOCK · LM3226
N–20 X 1O with NUT · FL3336
PRIMER WEDGE BAR with SCREW · LM3261
PRIMER ROCKER ARM · LM3239
ROCKER BOLT not visible · LM3227
ROCKER SPRING not visible · TP2115
Helpful setup
and
operation videos
available on
leeprecision.com
© 20 Lee Precision Inc.
Printed in USA
CRANK SLIDER
with SCREWS
FEED ROD
LM3262
FEED BRACKET
with NUT · LM3260
RAM · LM3237
INSIDE RAM
SPENT PRIMER DOOR · LM3233
DOOR SPRING · LM3234
SPRING RETAINER · LM3235
DRAW BOLT · LM3242
YOKE · LM3236
YOKE PIN · LM323O
YOKE PIN CLAMP not visible · LM3232
MASTER
-
FRAME · LM3223
CONNECTING LINK · LM3229
.7. 2
Lee Precision, Inc.
[ OPTIONAL ]
CASE COLLATOR · 90667
WOOD KNOB · TR2447
LEVER · LM3224
SHELL PLATE NUT w/ O-RING · RE1526
CASE EJECTOR · LM3241
CASE RETAINER · LM3246 4 req.
SHOULDER SCREWS · LM3265 4 req.
BELVILLE WASHERS · LM3263 4 req.
CARRIER · LM3238
WAVE WASHER · LM3208
– 20 NUTS · FM1371 · 4 req.
G
af
\
LINK PIN ·LM3256
GREASE FITTINGS · LM3248
LEE PRECISION, INC.
4275 Hwy. U · Har ford WI 53027
www.leeprecision.com
7538
CHECKED BY
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Lee Precision LOAD-MASTER
Summary of Contents for Lee Precision LOAD-MASTER
- Page 1 YOKE · LM3236 YOKE PIN · LM323O YOKE PIN CLAMP not visible · LM3232 LEE PRECISION, INC. 4275 Hwy. U · Har ford WI 53027 © 20 Lee Precision Inc. Printed in USA www.leeprecision.com .7. 2 Lee Precision, Inc. 7538...
- Page 2 The Lee Load-Master is the finest reloading machine ever built. To maximize its usefulness, the instructions should be read and fully understood. IMPORTANT YOU MUST DO THESE BEFORE YOU CAN RELOAD Bolt to a sturdy bench Install case inserter Adjust the dies...
- Page 3 The lef end of the bracket should be parallel The Perfect Powder Measure has been with the Load-Master right mounting lug. attached to the univ er sal charging die and the proper drop tube is installed. The rest...
-
Page 4: Preliminary Testing
Now lower the ram and attach the pen- Near the bottom of the stroke the lever will Filling the Primer Feeder dant to the bead chain with just enough push against the indexer and smoothly ro- tension to rotate the drum to the fill posi- tate the shell plate exactly 72. -
Page 5: Operation
If the shell head is of a di erent size it is station by swinging out the case retainer. also necessary to replace the shell plate. The shell plates for the Load-Master are Case Feeder the easiest of all to change. - Page 6 Changing Dies spring is installed into the hole at the rear of the primer punch. Now slip the primer Specific die installation instructions are not included in this manual. trough over the punch. Push down on Always follow the instructions included with the dies. the lef end of the priming rocker arm to WHEN INSTALLING DIES be sure everything is working freely.
-
Page 7: Troubleshooting
FIGURE 4 Alignment of the Carrier to the Turret PULL-OUT RIB This is an adjustment that need never be done unless you disassemble the carrier from the ram. The draw bolt head, at the bottom of the ram, MUST be loosened so the carrier can be rotated on INDEX FLIPPER the end of the ram. - Page 8 List of Sizes Accessories Part No. CARTRIDGE SHELL PRIMER CASE CARTRIDGE SHELL PRIMER CASE RIFLE PLATE SIZE FEEDER Large Primer Feeder 90077 ......... PISTOL PLATE SIZE...
Need help?
Do you have a question about the LOAD-MASTER and is the answer not in the manual?
Questions and answers