See the Electromagnetic information, in-service training, or current literature, Compatibility section. contact your Stryker sales representative or call • Upon initial receipt and before each use, Stryker customer service at 1-269-323-7700 or operate the equipment and inspect each 1-800-253-3210.
Page 3
000) are supplied with the Universal Battery otherwise specified. Charger. • DO NOT modify any equipment without the • Four Stryker F1 Charger Modules (REF 1900- authorization of the manufacturer. 125-000) are supplied with the Stryker F1 • Use only Stryker-approved electronic Universal Battery Charger.
Page 4
Ethernet receptacle used to export Indicator Lights – Provide status device usage data from the battery information for each charger module. charger to Stryker via Stryker’s Cloud, if desired. Information Screen – Provides status information and error messages for the Ethernet Cable (not supplied) –...
Page 5
Input Button Label Area – Displays appropriate input button labels during the battery pack charging sequence. MAC ID Media Access Control Identifier Stryker F1 battery pack orientation Refer to instruction manual/booklet General warning sign CSA Group certification mark for United States and Canada.
Page 6
• Confirm with a facility IT representative that the Ethernet receptacle has access to Stryker’s Cloud. • See the Network Requirements in the Specifications section. • For more information, contact your Stryker Figure 5 – Error Code sales representative. www.stryker.com...
Page 7
• The charging sequence may take between 5 and 120 minutes, based on the type of battery pack and the existing level of charge in the battery pack. • On the Stryker F1 Universal Battery Charger, always install Stryker F1 SmartGrip ® Battery Modules in the proper orientation (figure 6).
Page 8
To Replace a Charger Module charger modules in liquid. • DO NOT use solvents, lubricants, or other See the instructions for use supplied with the chemicals to clean the battery charger or replacement charger module. charger modules unless otherwise directed. www.stryker.com...
• DO NOT sterilize the battery charger or • If the equipment fails to meet the inspection charger modules. and testing criteria, contact your Stryker sales representative or call Stryker customer service. Outside the US, contact your nearest Stryker 1. Disconnect the power cord from the facility subsidiary.
Page 10
Do not dispose of as unsorted municipal waste. Contact local distributor for disposal information. Ensure infected equipment is decontaminated prior to recycling. NOTE: Contact Stryker for the recycling passport for this product. China RoHS Standard SJ/T 11364 To comply with China RoHS Standard SJ/T 11364, this device has been marked with the environmentally-friendly use period (EFUP) number, measured in years.
WARNING: DO NOT disassemble or service this equipment. Failure to comply may result in electric shock or fire. NOTE: For service, contact your Stryker sales representative or call Stryker customer service. Outside the US, contact your nearest Stryker subsidiary. PROBLEM...
Page 12
Stryker F1 battery Push the release button pack release button during installation. is not allowing proper installation. Stryker F1 battery pack Reinstall battery pack in is not installed in the the correct orientation. correct orientation. Contacts are dirty or Clean the battery pack.
Page 13
Information screen does not Battery pack Battery pack is not a Use Stryker battery display charge cycle count Stryker-approved battery packs only. information. pack. Battery pack/ Battery pack (REF 4112- No action required.
Page 14
Battery pack was Replace the battery repaired by an pack. unauthorized provider and is not programmed. Battery pack is not a Use Stryker battery Stryker-approved battery packs only. pack. Charger module Charger module contact Clean the charger is corroded.
DHCP server, Mask and Gateway provided by site IT admin; Access to Configuration: Stryker’s Cloud Technical Standard TCP/IP over Ethernet (IEEE 802.3 10/100 Mbs), utilized industry Specifications of the standard https (port 443) web services communication to Stryker’s Cloud. Connection: Intended Information Device Usage Data Flow: Hazardous Situations None known.
Page 16
“GROUNDING RELIABILITY CAN ONLY BE ACHIEVED WHEN EQUIPMENT IS CONNECTED TO AN EQUIVALENT RECEPTACLE MARKED ‘HOSPITAL ONLY’ OR ‘HOSPITAL GRADE’ ” or equivalent wording. Agency Approval: CSA Certified for Canada and US or UL Recognized for Canada and US. www.stryker.com...
7110-190-000) are intended for use in the electromagnetic environment specified below. The customer or the user of the Universal Battery Charger (REF 7110-120-000) and Stryker F1 Universal Battery Charger (REF 7110-190-000) should assure that they are used in such an environment.
Page 19
7110-190-000) are intended for use in the electromagnetic environment specified below. The customer or the user of the Universal Battery Charger (REF 7110-120-000) and Stryker F1 Universal Battery Charger (REF 7110-190-000) should assure that they are used in such an environment.
Page 20
7110-190-000) are intended for use in the electromagnetic environment specified below. The customer or the user of the Universal Battery Charger (REF 7110-120-000) and Stryker F1 Universal Battery Charger (REF 7110-190-000) should assure that they are used in such an environment.
Page 21
If the measured field strength in the location in which the Universal Battery Charger (REF 7110-120-000) and Stryker F1 Universal Battery Charger (REF 7110-190-000) are used exceeds the applicable RF compliance level above, the Universal Battery Charger (REF 7110-120-000) and Stryker F1 Universal Battery Charger (REF 7110-190-000) should be observed to verify normal operation.