Subscribe to Our Youtube Channel
Related Manuals for Lumberjack BGS125
Summary of Contents for Lumberjack BGS125
- Page 1 SAFETY AND OPERATING MANUAL 250W Wet & Dry Bench Grinder BGS125 O RIGINAL INSTRUCTIONS BGS125...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Welcome to Lumberjack! Dear Customer, Congratulations on your purchase. Before using the product for the first time please be sure to read these instructions for use. They provide you with all the information necessary for using the product safely and to ensure its long service life. -
Page 3: General Power Tool Safety Warnings
A wrench or a key left c) Do not expose power tools to rain or wet attached to a rotating part of the power tool may conditions. Water entering a power tool will result in personal injury. increase the risk of electric shock. BGS125... - Page 4 Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. BGS125...
- Page 5 Stay alert and exercise control. Watch what operatio n. you are doing and use common sense. do not operate tool when you are tired. do not rush. BGS125...
- Page 6 The smaller the gauge number of the wire the greater the capacity of the cord. f) When using a cable reel, always unwind the cable completely. BGS125...
-
Page 7: Sy Mbols & Machine Details
Power Consumption - 250W Eye Shield Water 320rpm 200 x No loa d Speed - Wet Bath Tool Rest Stone D iameter - Dry 25mm 125 x Stone Diameter - 50mm Gross W eight - 16.7kg 17kg Nett Weight - BGS125... -
Page 8: What's Included
Eye shield mounting bar Eye shield mounting bracket Universal support bar Square edge jig Threaded bolt Universal support bar holder Mounting bar square bracket Support bar Tool rest, nut & washer Water trough drain hose 01 01 01 01 06 BGS125... -
Page 9: As Sembly
ASSEMBLY INSTRUCTIONS BGS125... - Page 10 ASSEMBLY INSTRUCTIONS BGS125...
- Page 11 ASSEMBLY INSTRUCTIONS BGS125...
-
Page 12: Operating
25°. The chart below gives you some guidance as to which angle is most suited to Mark the bevel with a marker to allow you to see where which materials. the grinding will occur. BGS125... - Page 13 Make sure the heel of the bevel touches the grinding stone, see fig 06-08. Turn the wet stone (I) by hand to check the full width of the ‘Primary Bevel’ is in contact with the stone. Make adjustments to the universal support bar until even contact. BGS125...
- Page 14 When finished switch off had their reverse side flattened and honed so that it is as the grinder. equally fine as the bevel edge is ground. SWITCH OFF THE MACHINE! BGS125...
-
Page 15: Maintenance And Service
Therefore, no further lubrication is required. Power supply cord replacement If replacement of the power supply cord is necessary, this must be done by an authorised service centre in order to avoid a safety hazard. BGS125... -
Page 16: Lumberjack Guarantee
If a 1.2.3 If as ked to do so by Lumberjack or its return is requested by the Authorised Dealer or Authorised dealer, you return the product at Lumberjack, you will be provided with a Returns your own cost to Lumberjack’s or supplying... - Page 17 LUMBERJACK GUARANTEE of purcha se to Lumberjack. If you include a contact number with this it will speed your claim 2.4 Pleas e note that it is essential that the letter of claim reaches Lumberjack on the last day of this Guarantee at the latest.
-
Page 18: De Claration Of Conformity
Old Heat h Road, Wolverhampton, WV1 2RP. Tel : 01902 450 470 Declare s that the Wet & Dry Bench Grinder (BGS125) Is in com pliance with the regulations included in the Directives:2006/95/EC EC DECLARATION OF CONFORMITY Certifica te for EC-type examination delivered by Intertek Testing Services Ltd.,Shanghai,ETL Semko Building No.86,1198 Qinzhou Road(North),Caohejing Development Zone,Shanghai 200233,China. -
Page 19: Parts List
F bar support piece Capacitor 14μF/300V Locking knob M6x16 Capacitor support Spark deflector Type I hex nut M8 Flat washer D5 Phillips screw M5x12 Phillips screw M5x8 Power cord Hex screw M3x10 Cir-clip for shaft D15 Small cover plate Bearing BGS125... -
Page 20: Parts Diagram
Parts Diagram BGS125...
Need help?
Do you have a question about the BGS125 and is the answer not in the manual?
Questions and answers