TABLE OF CONTENTS SERVICE SAFETY PRECAUTIONS ............................ 3 IMPORTANT INFORMATION ............................... 5 CLEANING ................................... 6 SERVICE MODE .................................. 7 DESIGN MODE ..................................10 LOCATION OF CONTROLS ..............................11 LAYOUT OF MAJOR BOARDS ............................13 MECHANICAL DISASSEMBLY ............................14 EXPLODED VIEW ................................17 PACKING DISASSEMBLY ..............................
SERVICE SAFETY PRECAUTIONS • The caution items shown here describe major safety issues and should always be observed. • The meanings of the various indications are as follows. Indicates a hypothetical situation in which service personnel and nearby third parties, or even WARNING end users due to a product defect after the service operation is completed, could possibly be in danger of injury or even death in the event of operational error.
Page 4
WARNING • Always advise users to keep children away. There is danger of injury to children from tools, disassembled products, etc. KEEP CHILDREN AWAY • Always disconnect the power plug before starting work whenever power is not required. Failure to disconnect the power plug before starting work can result in electrical shock. UNPULUG •...
IMPORTANT INFORMATION About Permanent after-image • Due to the characteristics of a plasma screen, if the same image is displayed for an extended period of time, permanent after-image (image retention) in part of the screen may result. As a result of accu- mulative effect, brightness deterioration results.
CLEANING Remove the power plug before cleaning. Do not use solvents such as benzine or thinner to clean the TV. – These solvents may distort the cabinet or damage its finish. – If rubber or vinyl products remain in contact with the TV for a long time, a stain may result.
SERVICE MODE 1. ENTERING TO SERVICE MODE 1) Press o button once on 2) Press o button again to 3) While pressing the o button, Remote Control. keep pressing. press MENU button on TV set. Item Data or Sound Mute (Service mode display) 2.
Page 8
4. SELECTING THE ADJUSTING ITEMS 1)Every pressing of CHANNEL s button in the service mode changes the adjustment items in the order of table-2. (t button for reverse order) 5. ADJUSTING THE DATA 1) Pressing of VOLUME ; +/– button will change the value of data in the range from 00H to FFH. The variable range depends on the adjusting item.
Page 9
The diagnosis will begin to check if interface among IC’s are executed properly. 2) During diagnosis, the following displays are shown. WP48_EURO 42WP46P Firmware: Version information of microprocessor In case of file name : WP48_EURO and Version : 1.00 indicates[WP48_EURO_100].
DESIGN MODE 1. ENTERING TO DESIGN MODE 3) The following displays 1) Select the Service mode. 2) While pressing CALL button on Remote and press MENU button on TV. are shown on the screen Press Press WP48_EURO (Design mode) Version information of microprocessor Main tuner information Sub tuner information...
LOCATION OF CONTROLS Front INPUT 5 (EXT 5) GREEN – On-timer set Power Button RED – Power On Back BRACKET HOLES decoder* video recorder IN/OUT SCART 1 (EXT 1) SCART 2 (EXT 2) SCART 3 (EXT 3) MAINS LEAD SUPPLIED COMPONENT VIDEO INPUT (EXT 4) CONECTING A COMPUTER...
Page 12
OK to confirm your selection Teletext control buttons Stereo/Bilingual reception Bass Boost/Super Woofer To select mode To mute the sound When in TV mode: When using a TOSHIBA VCR or DVD: Time display press to PAUSE When in Teletext mode: press to EJECT...
• The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model number and Description. ∗ • The PC board assembly with mark is no longer available after the end of the production. Model : 42WP46P Capacitors ..... CD Ceramic Disk : Plastic Film : Electrolytic Resistors ....
Page 21
Location Location Parts No. Description Parts No. Description C6073 24100104 CERAMIC CHIP, 25V F 0.1UF Z CS16 24092731 CERAMIC CHIP, 16V B 1UF K C6075 24619313 16V 470UF 16SGV470M8X10.5 CS26 24619100 ELECTROLYTIC, 16V 10UF M C6088 24619313 16V 470UF 16SGV470M8X10.5 CS39 24092573 CERAMIC CHIP, 16V B 0.47UF K...
Page 22
Location Location Parts No. Description Parts No. Description CV47 24092538 CERAMIC CHIP, 10V F 1UF Z R677 24011473 CHIP, 1/20W 47K OHM J CV48 24092538 CERAMIC CHIP, 10V F 1UF Z R684 24871229 CHIP, 1/8W 2.2 OHM J CV49 24092538 CERAMIC CHIP, 10V F 1UF Z R685 24871229...
Page 23
Location Location Parts No. Description Parts No. Description RB02 24011471 CHIP, 1/20W 470 OHM J RS03 24011101 CHIP, METAL FILM, 1/20W 100 OHM J RB10 24011682 CHIP, METAL FILM, 1/20W 6.8K OHM J RS04 24011101 CHIP, METAL FILM, 1/20W 100 OHM J RB11 24011103 CHIP, METAL FILM, 1/20W 10K OHM J...
Page 24
Location Location Parts No. Description Parts No. Description RS79 24011101 CHIP, METAL FILM, 1/20W 100 OHM J RV61 24011103 CHIP, METAL FILM, 1/20W 10K OHM J RS80 24011472 CHIP, 1/20W 4.7K OHM J RV63 24011100 CHIP, METAL FILM, 1/20W 10 OHM J RS81 24011102 CHIP, METAL FILM, 1/20W 1K OHM J...
Page 30
FRONT AV BOARD PD1944A2 (U001B) KEY BOARD PD1944A3 (U001C) LED/RMT BOARD PD1944A4 (U001D) BOTTOM (FOIL) SIDE BOTTOM (FOIL) SIDE BOTTOM (FOIL) SIDE VIDEO MENU VOL DN VOL UP POS UP POS DN +5V-1 PV61 PV60 SA01 SA03 SA04 SA06 SA02 SA07 E3-L RA73...
Page 33
SCALER BOARD PD1901G1 (U003A) TOP (COMPONENT) SIDE - 38 - - 39 -...
Page 34
SCHEMATIC DIAGRAM MODEL : 42WP46P WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
TABLE OF CONTENTS SERVICE SAFETY PRECAUTIONS ............................ 3 SERVICE MODE .................................. 5 LOCATION OF CONTROLS ............................... 10 LAYOUT OF MAJOR BOARDS ............................12 MECHANICAL DISASSEMBLY ............................13 EXPLODED VIEW ................................15 PACKING DISASSEMBLY ..............................17 CHASSIS AND CABINET REPLACEMENT PARTS LIST ....................18 PC BOARDS TOP &...
SERVICE SAFETY PRECAUTIONS • The caution items shown here describe major safety issues and should always be observed. • The meanings of the various indications are as follows. Indicates a hypothetical situation in which service personnel and nearby third parties, or even WARNING end users due to a product defect after the service operation is completed, could possibly be in danger of injury or even death in the event of operational error.
Page 42
WARNING • Always advise users to keep children away. There is danger of injury to children from tools, disassembled products, etc. KEEP CHILDREN AWAY • Always disconnect the power plug before starting work whenever power is not required. Failure to disconnect the power plug before starting work can result in electrical shock. UNPULUG •...
SERVICE MODE 1. ENTERING SERVICE MODE 1) Press button once on 2) Press button again and 3) While pressing the button, Remote Control. keep pressing. press MENU button on TV set. or Sound Mute (Service mode display) DISPLAYING THE ADJUSTMENT MENU 1) Press MENU button on TV.
Page 44
4. SELECTING THE ADJUSTING ITEMS 1) Every pressing of CHANNEL s button in the service mode changes the adjustment items in the order of table-2. (t button for reverse order) 5. ADJUSTING THE DATA 1) Pressing of VOLUME ; +/– button will change the value of data in the range from 00H to FFH. The variable range depends on the adjusting item.
Page 45
SELF DIAGNOSTIC FUNCTION 1) Press “9” button on Remote Control during display of adjustment menu in the service mode. The diagnosis will begin to check if interface among IC’s is executed properly. 2) During diagnosis, the following displays are shown. WP56_EU_0100 WP56_EU_0100 000000...
Page 46
VERSION CHECK MODE 1) Press “9” button twice on Remote Control during display of adjustment menu in the service mode. The version of main MPU will begin to check. 2) During Version Check, the following displays are shown. WP56_EU_0100 (E16) LG −...
Page 47
10. STATUS CHECK MODE 1) Press “9” button thrice on Remote Control during display of adjustment menu in the service mode. The status of this model will begin to check. 2) During Status Check, the following displays are shown. EXT1 1080i-50 C6 38 54 CE 08 0000 0000 0000...
LOCATION OF CONTROLS CONTROLS AND INPUT CONNECTIONS INPUT 3 (EXT 3) Standby GREEN – On-timer set RED – Power On CONNECTING EXTERNAL EQUIPMENT BRACKET HOLES decoder* MEDIA REC. media recorder IN/OUT SCART 1 (EXT 1) MAINS LEAD SUPPLIED SCART 2 (EXT 2) - 10 -...
Page 49
OK to confirm your selection Text control buttons Stereo/Bilingual reception Bass Boost To select mode To mute the sound When in TV mode: When using a TOSHIBA VCR or DVD: Time display press to PAUSE When in text mode: press to EJECT...
CHASSIS AND CABINET REPLACEMENT PARTS LIST WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “SERVICE SAFETY PRECAUTIONS” ON PAGE 3 OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 66
FRONT AV BOARD PD2206A2 (U003B) FRONT AV BOARD PD2206A2 (U003B) BOTTOM (FOIL) SIDE TOP (COMPONENT) SIDE RV122 PV60 GR605 PV61 GR604 RV123 P661 R687 R690 PD2206 -2 R692 R688 CY650 CY650 R689 R691 D653 D653 23590293 C605 DV121 D652 PV25B LV121 LC31 P601B...
Page 67
SCHEMATIC DIAGRAM MODEL : 42WP56P WARNING : BEFORE SERVICING THIS CHASSIS, READ THE "SERVICE SAFETY PRECAUTIONS" ON PAGE 3 OF THIS MANUAL. CAUTION : The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 70
QE70 OPEN PJ62A LE71 LE70 OPEN OPEN OPEN 4400mA 3.3VD_a RE74 3300mA OPEN GJ70 CE71 3.3VD_b OPEN DE72 OPEN CE70 RE70 OPEN OPEN OPEN DE71 OPEN RE73 OPEN TO DB QE30 OPEN (US HP95) PJ63A OPEN QE10 SI-3090CA QE10A LE31 LE10 RE10 LE30...
Page 73
H001 GR613 GR612 ENG37A13GF OPEN GR113 GR112 OPEN OPEN OPEN TIF Type : Horizontal ANT IN TUNER-GND TUNER-GND Q102 9-A1 5V3TN OPEN R112 OPEN C114 OPEN C119 23367329 OPEN OPEN B25V0.01 R115 OPEN OPEN PK01 R111 OPEN OPEN R113 OPEN R114 OPEN RM73B1HR00OD...
Page 98
Note: For GATE of IC705 During, POD STANDBY mode of GATE_BTXD line, it keeping at SW1.8V mode. Normally, when power is ON, POWER_DB line (L:ON) is shut-off whichever pin No.1 or 2 of IC 707 is OFF. 42WP56P SIGNAL MICRO I/O (29/52)
Page 103
Note: Normally, I2C Bus Lines (SDA_STBY, SCL_STBY), these are connected to Cortez line. When I2C Bus Lines are POD STBY mode, these are connected to DB line. 42WP56P SIGNAL STD-BY MICRO (34/52)
Page 109
Note: I2C Bus lines switching for Stand-by Micom. SW1.8V to H (normally): Connect to Cortez SW1.8V to L (POD STBY mode): Connect to DB] 42WP56P SIGNAL I2C Switch (40/52)
SCHEMATIC DIAGRAM MODEL : 42WP46P WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 127
Y_BM C E3 S SW E3 C_BM E3 V GND YV E3 L_BM ASIA L E3 R_BM R E3 POWER TUNER GND TX_BM TUNER GND RX_BM DET_HP P515A 1P PLUG 42WP46P P516A 1P PLUG SIGNAL UNIT CONNECTION AUDIO OUT (1/60)