Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ANTUMBRA PATH
Summary of Contents for ANTUMBRA PATH
- Page 1 ANTUMBRA PATH MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS 01. INSTALLATION 02. BACK 03. FRONT 04. USE 05. CV/TRIGGER INPUT 06. RESET INPUT 07. SEQUENCE LENGTH 08. DIRECTION 09. CHAIN MODE 10. NOTE... - Page 3 00. THANK YOU! Thank you for purchasing the Antumbra PATH module! In this documentation you can find information about the installation and use of the module.
-
Page 4: Installation
01. INSTALL ATION When you turn the PATH around, you should see the mod- ule as it is on the left illustration. Connect your power header to the 10 pin connector on the bottom. Pay atten- tion to the orientation of the cable, the... -
Page 5: Back
02. BACK With the three pin header you can turn on or off the jack lights. Top position is off, bottom is on. Turning on the jack lights draw about 75mA more from the +12V rail. MCP6002 JACK LIGHTS SWITCH... -
Page 6: Front
03. FRONT CH1 LED CH2 LED CH1 BUTTON CH2 BUTTON CH1 CV/TRIG INPUT CH2 CV/TRIG INPUT CH1 RESET INPUT CH2 RESET INPUT CH1 INS/OUTS CH 2 INS/OUTS CH1 COM IN/OUTPUT CH2 COM IN/OUTPUT (NORMALIZED TO 5V) (NORMALIZED TO 5V) -
Page 7: Use
04. USE PATH consists of two 4:1 switches or one 8:1 switch. You can use it in two ways regarding the switching: 1. Insert signals in the 4 I/O jacks and switch between them so that the selected signal comes out on the bottom I/O jack. -
Page 8: Cv/Trigger Input
05. CV/TRIGGER INPUT Pressing the channel button switches between CV/trig- ger input modes. When the channel LEDs are unlit it means that the chan- nel CV/trigger input expects triggers. On the rising edge of a trigger it’ll step to the next I/O channel. When the channel LED is solidly lit, it means the channel CV/trigger input expects CV between 0-5V. - Page 9 05. CV/TRIGGER INPUT CV is split between the available steps set in the sequence length page, meaning that if there are 4 steps available, the CV will change channel every 5/4=1.25V. 8 STEPS 7 STEPS 6 STEPS 5 STEPS 4 STEPS 3 STEPS 2 STEPS I/O 1...
-
Page 10: Reset Input
06. RESE T INPUT Trigger mode: On the rising edge of a trigger in the reset input the se- quence goes back to step one. CV mode: On the rising edge of a gate in the reset input the current CV is held on the value it currently is. -
Page 11: Sequence Length
07. SEQUENCE LENGTH Hold the channel button until it starts blinking. The available steps are lit by the channel color. Press- ing the button repeatedly cycles through 2-4 steps or in chain mode 5-8 steps. Long press the channel button again to exit this mode. -
Page 12: Direction
08. DIRECTION Hold the channel button, first it starts blinking, then if you keep pressing it, it’ll start blinking faster, now you can release it. This mode determines the step direction of the channel, you can cycle through the directions by repeatedly press- ing the channel button. -
Page 13: Chain Mode
09. CHAIN MODE Press both channel buttons at once, now the two channels BUTTON are one and this group is controlled by the CH1 controls (Button, CV, Reset). CV/TRIG INPUT The COM I/O of the 8:1 switches is the CH1 COM I/O jack. RESET INPUT If you want to split the channels again, just press the two buttons at once. -
Page 14: Note
10. NOTE Due to the fast switching, pops can be heard when audio is being switched. - Page 15 PATH is designed by David Szebenyi under Antumbra. www.antumbra.eu Manual by David Szebenyi (www.aman.hu) 2020 • All rights reserved!
Need help?
Do you have a question about the PATH and is the answer not in the manual?
Questions and answers