Xenios WOD TIMER User Manual page 7

OPERATION MANUAL:
3. Beeper and Pre-Workout-Countdown setting: The WOD Timer is equipped with an internal beeper to loud-notice some events. Its software
is furthermore programmed to display a 10 seconds pre-workout-countdown, with beeper on last 3 seconds.
(sometimes the user who control the Timer with the remote, needs to train himself as well, so the pre-workout-countdown helps him to leave
the remote down and to join the training group).
Attention: to use the button
Press and the Timer displays
two digits on the right side can be adjusted by using the numeric pad on the remote, to switch ON/OFF either the Beeper (anytime the beeper is
required. Example: training timer pacer) and the Pre-Workout-Countdown (see Interval Timer Operation Manual section). Once set, just confirm
the data by pressing .
4. Press
to enter into clock/temperature mode. Timer alternate displays clock and temperature according to the entered general settings.
While the Timer is waiting for data to be entered (any setting procedure), the
Attention: Anytime the Timer is waiting for data entering by the user, and nothing happens within 90 seconds, it will go back to
clock/temperature mode by itself (timeout function).
STOPWATCH OPERATION MANUAL:
1. Press
to enter the Timer in to the Stopwatch function. The Timer shows
.Press to start the count-up stopwatch.
.Press to stop the stopwatch and to hold on the display the recorded time.
.Press to go back to
.While the stopwatch is working, press
the time on background. Press
Press to just go back to
Attention: if Beep-Pacer was set for stopwatch (see below number 2.), while the stopwatch is working on background for LAP
function, the beeper keep sounding too at the set pacer-time).
2. Stopwatch Beep-Pacer setting: press
The former stands for beep-pacer ON, while the latter stands for beep-pacer OFF. To switch pacer ON/OFF, just use the buttons
P- : 00 : 00
and . To set the pacer time (minutes and seconds), just enter MM : SS by using the numeric pad on the remote (enter a value between
and 99), then confirm all settings and data with
00 : 0 1 99 :
Example, if you set 05, the pacer beeps every 5 seconds, while the stopwatch is running.
P : 00 :
To go back to the Stopwatch, just press again
Attention: the beep-pacer function is not available if the beeper is deactivated by the general settings (see General Settings
Operation Manual at item 3) ).
3. COUNT-DOWN STOPWATCH: if it would be necessary to use the stopwatch as a count-down (example: to quickly set and perform an AMRAP
workout (As More Reps As Possible – within a set time) ), once the Stopwatch function has been selected
Timer displays -. So press
SP : dn : -
(or the latest set value) and the first left-side digit will start blinking. Countdown time could be set by using the numeric pad and/or the
00 : 00 : 00
, . Once set the Countdown time, just confirm it by pressing
of the Count-Up one ,
just use the button after having entered in to the Count-Down Stopwatch function.
Attention: the Stopwatch beeper function could be set also for Count-Down feature.
ALARM OPERATION MANUAL:
1. Press
to enter the Timer in to the Alarm function. The Timer shows
mark "-" isn't displayed) / OFF ("-" is displayed). The second digit (from 1 to 9) stands for the Alarm is being set (The Timer can store up to 9
different Alarms). The rest of the editable digits stand for HH:MM (time the Alarm will sound).
Attention: the Alarm setting mode can be entered just while the Timer is on Clock mode. While the Timer is on any other mode, the
button will be deactivated.
WOD TIMER
to select one of the three beeper volume levels.
00. The first letter "P" stands for Pacer, while the second letter "C" stands for Countdown. The last
PC : - - :
. stands for Beeper OFF and Pre-Workout-Countdown OFF.
pc : - - : 00
. stands for Beeper OFF and Pre-Workout-Countdown ON.
pc : - - : 0 1
. stands for Beeper ON and Pre-Workout-Countdown OFF.
pc : - - : 1 0
. stands for Beeper ON and Pre-Workout-Countdown ON.
pc : - - : 1 1
00. (If is pressed while stopwatch is working, the Timer will go back to
00 : 00 :
to activate the LAP function. Timer stops just on display while it keeps counting
to display again the count-up from the value it has reached by working on background.
00 : 00 : 00.
after having entered in to the stopwatch function. The Timer will display
.
and the Timer displays
to set and/or modify the time to be counted down by the Stopwatch
, , . If it wouldn't necessary to set and/or amend a Count-Down time (so to use the latest set),
button is not activated.
00 : 00 : 00.
00 : 00 : 00.
. The Count-Down Stopwatch will work with the same operation buttons
00. The first digit on the left side stands for Alarm ON (minus
- 1 : 00 :
as well).
00 : 00 : 00
00, or
P : 00 :
, press the button and the
. The Timer displays
MM : ss : ss
7