Advertisement
The SA12/S.V2 Medium Stroke Air Hammer, when operated in accordance with these instructions and tested in accordance with EN
28662-2: 1994 results in the following vibration emission declared in accordance with BS EN12096: 1996.
Measured vibration emission value: . . . . . . .25.3m/s2
These values are suitable for comparison with emission levels of other tools that have been subject to the same test.
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
Recommended Measures to reduce risk of hand-arm vibration syndrome:
This tool should not be used by an individual regularly for more than 117 minutes in any 8 hour period.
This duration of use should be reduced if the individual is exposed to hand-arm vibration from other sources.
4. OPERATING INSTRUCTIONS
Note: Numbers in brackets refer to item numbers in the parts list.
The air hammer is designed primarily for use on vehicle bodywork. We do not recommend any other use. Ensure you read, understand and
follow the safety instructions in Section 1.
4.1.
Attach the retaining spring (17) by screwing it onto the cylinder (16).
4.2.
Insert the chisel using the hooked end of the spring to hold the chisel in place.
4.3.
Attached the tool to the air supply (see Section 2).
4.4.
To operate the hammer, squeeze the trigger (6). The air regulator (5) may be used as a means of throttle control.
5. MAINTENANCE
WARNING! Disconnect the hammer from the air supply before changing chisels, servicing or performing any maintenance.
5.1.
Keep the hammer oiled for optimum performance. Lubricate with a good grade of air tool oil such as Sealey ATO/500 or ATO/1000.
If there is no oiler in the air system then a teaspoon of oil can be poured into the air inlet of the hammer, or into the hose at the nearest
connection to the air supply. Then run the hammer for a short time.
Note: The following external factors may cause loss of power and effect hammer performance:
The air supply. Reduced compressor output, excessive drain on the air line, moisture or restrictions in air pipes or the use of hose connectors
having too small a bore. Correct as necessary.
The hammer. Grit or gum deposits in the tool. Correct by cleaning the air strainer and flushing out the tool with gum solvent oil or an
equal mixture of SAE No.10 oil and kerosene. If, despite taking action as above, the tool function is still impaired, contact your local
Sealey service agent.
6. SPARE PARTS
Item Part No.
Description
1
SA12R/01 Handle
2
SA12R/02 Pin
3
SA12R/03 Ball Seat
5
SA12R/05 Air Regulator & O-ring
6
SA12R/06 Trigger
8
SA12R/08 Pin & O-ring
9
SA12R/09 Pin Seat
10
SA12R/10 Throttle Spring
11
SA12R/11 Hose Adaptor
12
SA12R/VA Valve Assembly
15
SA12R/15 Piston
16
SA12R/16 Cylinder
17
SA11R/17 Spring Retainer
18
SA12S.C
5pc Chisel Kit
(Not Shown)
Issue No:
1
Date Issued: 260804
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Risk of Hand Arm Vibration Injury.
Uncertainty: . . . . . . . . . . . . . . . . 10.12m/s2
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
www.sealey.co.uk
01284 757500
Web
sales@sealey.co.uk
01284 703534
email
SA12/S.V2
Issue: 2 - 04/11/09
Advertisement
