Sealey SA120.V2 Instructions

Thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLeAse ReAD These INsTRUCTIONs CAReFULLY. NOTe The sAFe OPeRATIONAL ReQUIRemeNTs, WARNINGs & CAUTIONs. Use The
PRODUCT CORReCTLY AND WITh CARe FOR The PURPOse FOR WhICh IT Is INTeNDeD. FAILURe TO DO sO mAY CAUse DAmAGe AND/OR
PeRsONAL INJURY AND WILL INVALIDATe The WARRANTY. KeeP These INsTRUCTIONs sAFe FOR FUTURe Use.
1. sAFeTY
 WARNING! Ensure Health & Safety, local authority, and general
workshop practice regulations are adhered to when using this
equipment.
 WARNING! Disconnect the hammer from the air supply before
changing accessories, servicing or performing any maintenance.
 Keep the hammer clean and maintain it in good condition (use an
authorised service agent).
 Replace or repair damaged parts. Use genuine parts only.
Unauthorised parts may be dangerous and will invalidate the
warranty.
 Keep the work area clean, uncluttered and ensure there is
adequate lighting.
 Ensure chisels are correctly rated for the job, and DO NOT use
damaged or suspect chisels.
 WARNING! Wear approved safety eye or face protection, ear
defenders, and if dust is generated, respiratory protection.
 Keep hands and body clear of the work when operating the
hammer.
 Maintain correct balance and footing. Ensure the floor is not
slippery and wear non slip-shoes.
 Remove ill fitting clothing. Remove ties, watches, rings, and other
loose jewellery, and contain and/ or tie back long hair.
 Keep children and unauthorised persons away from the working area.
 Secure non stable work piece with a clamp, vice or other adequate
holding device.
 Avoid unintentional starting.
 WARNING! ensure correct air pressure is maintained and not exceeded.
2. AIR sUPPLY
the recommended hook-up is shown in fig 1.
2.1. Ensure the air valve is in the "off" position before connecting to the air supply.
2.2. You will require an air pressure of more than 6bar (90psi) , and an air volume of more than 4cfm for operating the unit.
2.3.  WARNING! Ensure the air supply does not exceed 140PSI while operating the hammer. too high an air pressure and unclean air
will shorten the product life due to excessive wear, and may be dangerous causing possible damage and/or personal injury.
2.4. Drain the air tank daily. Water in the air line will damage the tool.
2.5. Clean the air inlet filter screen weekly.
2.6. line pressure should be increased to compensate for unusually long air hoses (over 8 metres). the minimum hose diameter should
be 10mm I.D. and fittings must have the same inside dimensions.
2.7. Keep hose away from heat, oil and sharp edges. Check hoses for wear, and make certain that all connections are secure.
2.8 Couplings.Vibration may cause failure if a quick change coupling is connected directly to the wrench. to overcome this, connect a
leader hose to the wrench. A quick change coupling may then be used to connect the leader hose to the air line recoil hose. See fig 1 & 2.
fig.2
2. INTRODUCTION
the air hammer is designed primarily for use on vehicle bodywork. We do not recommend any other use. Contact your supplier immediately
should there be any missing, or damaged parts. Chisels not included.
© Jack Sealey limited
InStRUCtIonS foR:
AIR hAmmeR
MoDEl no:
fig.1
Original Language Version
sA120.V2
 Keep air hose away from heat, oil and sharp edges. Check air
hose for wear before each use, and ensure that all connections
are secure.
 DO NOT force the hammer to achieve a task it was not designed
to perform.
 DO NOT operate the hammer if any parts are damaged or missing
as this may cause failure or possible personal injury.
 WARNING! DO NOT cut, grind, saw, sand any materials
containing asbestos.
 DO NOT switch the hammer on whilst the chisel is in contact with
the workpiece.
 DO NOT carry the by the hose, or yank the hose from the air supply.
 DO NOT hold the workpiece by hand. Use clamps or a vice (not
included) to secure the workpiece. Available from your Sealey dealer.
 DO NOT allow untrained persons to operate the hammer.
 DO NOT operate the hammer when you are tired, under the
influence of alcohol, drugs or intoxicating medication.
 DO NOT use hammer where there is flammable liquids, solids or
gases such as paint solvents, including waste wiping or cleaning
rags etc.
 DO NOT leave the hammer operating unattended.
 DO NOT carry the hammer with your finger on the power switch.
 DO NOT direct air from the air hose at yourself or others.
 When work is complete ensure the air supply is turned off.
 When not in use disconnect from the air supply and store in a
safe, dry, child proof area.
SA120.V2 Issue: 3(SP) - 28/04/14