Troubleshooting/Specifications - LG DKS-5550Q Owner's Manual

Troubleshooting / Specifications
Check the following guide for the possible cause of a problem before contacting service.
Symptom
• The power cord is disconnected.
No power.
The power is on, but • No disc is inserted.
the DVD player does
not work.
• The TV is not set to receive DVD sig-
No picture.
• The video cable is not connected
No sound. • The equipment connected with the
• The power of the equipment connected
• The AUDIO options are set to the
• An unplayable disc is inserted.
The DVD player does
not start playback.
• The rating level is set.
• The remote control is not pointed at
The remote control
does not work properly.
• The remote control is too far from the
General
Power requirements . . . . . . . AC 110-240 V, 50/60 Hz
Power consumption . . . . . . . . . . . . . . . . . . . . . 14 W
Dimensions (approx.) .430 X 43 X 260 mm (w x h x d)
Mass (approx.) . . . . . . . . . . . . . . . . . . . . . . . . 2.3 kg
Operating temperature . . . 5˚C to 35˚C (41˚F to 95˚F)
Operating humidity . . . . . . . . . . . . . . . . . 5 % to 90 %
System
Laser . . . . .Semiconductor laser, wavelength 650 nm
Signal system . . . . . . . . . . . . . . . . PAL/NTSC/AUTO
Frequency
response . . . . . . DVD (PCM 96 kHz): 8 Hz to 44 kHz
DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
Signal-to-noise ratio . . . . . . . . . . . More than 100 dB
(ANALOG OUT connector only)
Harmonic distortion . . . . . . . . . . . Less than 0.008 %
Dynamic range . . . . . . . . . . More than 100 dB (DVD)
Design and specifications are subject to change without notice.
Manufactured under license from Dolby Laboratories. Dolby, MLP Lossless and the double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished works. Copyright 1992-1997 Dolby Laboratories. All rights reserved.
DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems, Inc.
P/NO : MFL39518837
Possible Cause
nal output.
securely.
audio cable is not set to receive DVD
signal output.
with the audio cable is turned off.
wrong position.
the remote sensor on the DVD player.
DVD player.
More than 95 dB (CD)
Correction
• Plug the power cord into the wall outlet
securely.
• Insert a disc. (Check that the DVD or audio
CD indicator in the display
window is lit.)
• Select the appropriate video input mode on
the TV.
• Connect the video cable securely.
• Select the correct input mode of the audio
receiver so you can listen to the sound from
the DVD player.
• Turn on the equipment connected with the
audio cable.
• Set the Digital Audio Output to the
correct position, then turn on the DVD play-
er again by pressing POWER.
• Insert a playable disc. (Check the disc type,
color system, and regional code.)
• Cancel the rating function or change the
rating level.
• Point the remote control at the remote sen-
sor of the DVD player.
• Operate the remote control closer to the
DVD player.
Outputs
VIDEO OUT . . . . . . . . . . . . . . . . . . . . . . .1 Vp-p 75 Ω,
sync negative, RCA jack x 1
Audio output (optical audio) . . . . . . . . .3 V (p-p), 75 Ω,
Audio output (analog audio) . . .2.0 Vrms (1 KHz, 0 dB),
600 Ω, RCA jack (L, R) x 1
Optical connector x 1