Table of Contents
Advertisement
Before Operation
AUDIO
Each DVD disc has a variety of audio output options.
Set the player's AUDIO options according to the type of
audio system you use.
AUDIO
Dolby Digital
DTS
MPEG
Sample Freq.
5.1 Speaker Setup
DRC
Vocal
Dolby Digital / DTS / MPEG
Bitstream: Select "Bitstream" if you connect the DVD
Player's DIGITAL OUT jack to an amplifier or other
equipment with a Dolby Digital, DTS or MPEG
decoder.
PCM : Select when connected to a two-channel digi-
tal stereo amplifier. DVDs encoded in Dolby Digital or
MPEG will be automatically downmixed to two-chan-
nel PCM audio.
Sample Freq. (Frequency)
If your receiver or amplifier is NOT capable of handling
96 kHz signals, select 48 kHz. When this choice is
made, this unit automatically converts any 96 kHz
signals to 48 kHz so your system can decode them.
If your receiver or amplifier is capable of handling 96
kHz signals, select 96 kHz. When this choice is made,
this unit passes each type of signal through without any
further processing.
Check the documentation for your amplifier to verify its
capabilities.
5.1 Speaker Setup
DVD
Select speaker settings, including volume balance and
distance, or test the speaker settings.
Speaker settings are only active on the Analog Multi-
Channel Output.
Speaker Setup
Make the following settings for the built-in 5.1 channel
surround decoder.
1. Press SETUP. The setup menu appears.
2. Use
/
to select the AUDIO option then press
to move to the second level.
3. Use
/
to select the Speaker Setup option then
press
to move to the third level. "Select" is high-
lighted.
4. Press SELECT/ENTER and 5.1 Speaker Setup
menu appears.
5. Use
6. Adjust options using
7. Press SELECT/ENTER to confirm your selection.
Speaker selection
Bitstream
Select a speaker that you want to adjust. [Front speaker
Bitstream
(Front L), Front speaker (Front R), Center Speaker
PCM
(Center), Subwoofer (Woofer), Rear speaker (Rear L) or
48 kHz
Rear speaker (Rear R)]
Select
On
On
Size
Since the speaker settings are fixed, you cannot change
Move
Select
the setting.
DVD
Volume
Press
speaker. (-5dB ~ 5dB)
Distance
If you have connected speakers to your DVD Player,
setting the Distance lets the speakers know how far the
sound has to travel to reach your set listening point.
This allows the sound from each speaker to reach the
listener at the same time.
Press
DVD
speaker.
Test
Select "All" to test the signals of each speaker.
Adjust the volume to match the volume of test signals
memorized in the system.
(When the size of the Front L/R speaker is selected to
"Large", the subwoofer (Woofer) is not available.)
Front L → Center → Front R → Rear R →Rear L → Woofer
You can adjust the volume during operating the test
tone, first use
option then use
speaker, so that all speaker's volume is same from the
listener's position.
Dynamic Range Control (DRC)
With the DVD format, you can hear a program's sound-
track in the most accurate and realistic presentation
possible, thanks to digital audio technology. However,
you may wish to compress the dynamic range of the
audio output (the difference between the loudest sounds
and the quietest ones). This allows you to listen to a
movie at a lower volume without losing clarity of sound.
Set DRC to On for this effect.
Vocal
Set Vocal to On only when a multi-channel Karaoke
DVD is playing. The karaoke channels on the disc will
mix into a normal stereo sound.
/
to select the desired speaker.
/
/
Returns to the previous menu.
/
to adjust the output level of the selected
/
to adjust the Distance of the selected
/
to select Volume or Speaker
/
buttons to select volume or
DVD
/
buttons.
DVD
11
Advertisement
Table of Contents
