Aquatic SERENITY W9AIR7444 Owner's Manual & Installation Manual

Table of Contents

Advertisement

Quick Links

Serenity Owner's Manual & Installation Guide
OWNER'S MANUAL &
INSTALLATION GUIDE
Installer: This booklet must be given to the product owner. Please add important information below.
Model # ___________________________________ Purchase Date ___________________________________
Serial # ___________________________________
Note: Read all instructions before proceeding with installation.
All specifications are ± 3/8'' and are subject to change without notice. Dimensions listed in inches (mm).
Aquatic
Distributor ___________________________________
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SERENITY W9AIR7444 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Aquatic SERENITY W9AIR7444

  • Page 1 Installer: This booklet must be given to the product owner. Please add important information below. Model # ___________________________________ Purchase Date ___________________________________ Serial # ___________________________________ Distributor ___________________________________ Note: Read all instructions before proceeding with installation. All specifications are ± 3/8’’ and are subject to change without notice. Dimensions listed in inches (mm). Aquatic...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS PRODUCT WARRANTY REGISTRATION INFORMATION IMPORTANT SAFETY INSTRUCTIONS 4 – 5 SERENITY AIR BATH USER INFORMATION FCC INFORMATION AQUATIC LIMITED WARRANTY INSTALLATION INSTRUCTIONS Pre-Installation Procedures Structural Preparation 9 – 11 Factory Installed Tile Flange Fast-Fill Water Spout for Serenity 33...
  • Page 3: Product Warranty Registration Information

    Serenity Owner's Manual & Installation Guide AQUATIC Product Warranty Registration Information Thank you for choosing an Aquatic bath. You have chosen one of the finest bath products in the industry! Aquatic supports your purchase with strong commitments to quality and customer satisfaction. IMPORTANT! To activate Product Warranty please register with Aquatic.
  • Page 4: Important Safety Instructions

    WARNING All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. Aquatic...
  • Page 5 • You have a medical history of heart disease, low or high blood pressure, circulatory system problems, or diabetes, consult with a physician before using an airbath. • You are under the influence of drugs, anticoagulants, stimulants, antihistamines, vasoconstrictors, vasodilators, hypnotics, narcotics, or tranquilizers. Aquatic...
  • Page 6: Serenity Air Bath User Information

    • If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. • The user may find the following booklet prepared by the FCC helpful: “How To Identify and Resolve Radio-TV Interference Problems.” It is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No., 004-000-00345-4. Aquatic...
  • Page 7 LIMITATIONS 1. Aquatic Air Baths sold for industrial, commercial or hotel use are warranted for two years, but not more than 3 years from date of manufacture, with a limited warranty that the shell will retain its structural integrity and configuration and be free of water loss due to a defect in the tub and the interior surface/face of the Air Bath is warranted against fading, blistering, cracking and delamination due to defects in the surface materials.
  • Page 8: Installation Instructions

    3. Plug in blower control box and run blower for 10 minutes. 4. Inspect the tub completely. Any defect must be reported to Aquatic prior to installation in order to have it covered by warranty. Should inspection indicate any damage or leaks, do not install the bath.
  • Page 9: Structural Preparation

    3. Tub must rest entirely on its base. DO NOT SUPPORT THE BASE OF THE TUB BY THE RIM. Aquatic strongly recommends preparing a bed of wet mortar in the area where tub is to be installed to assist in leveling and reduce vibration noise.
  • Page 10 PUMP END ACCESS PANEL ON PUMP END Corner Models Control Panel Notch 1" (25) 10" (254) 26" (660) " (1075) " (1075) ACCESS PANEL ON ACCESS PANEL ON Note: For Skirt PUMP END PUMP END Installation disregard front framing Aquatic...
  • Page 11 A - 6" x 12" (150 x 305) Box-outs 16" 16" B - Leveled Supports 1" (25) (405) (405) 1" x 3" (25 x 75) Ledgers PLYWOOD DECK C - 12" x 18" (305 x 460) minimum access DESIRED Aquatic...
  • Page 12: Factory Installed Tile Flange

    5 minutes. Carefully check for leaks both while blower is running and after it has been turned off. Allow water to stand in tub for at least 30 minutes before draining. AQUATIC WILL NOT BE RESPONSIBLE FOR WATER DAMAGE OF ANY KIND.
  • Page 13: Electrical Installation

    (4) fetal damage in pregnant women, (5) physical inability to exit the air bath, (6) unconsciousness resulting in the danger of drowning. WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia. Aquatic...
  • Page 14: Electrical Connections

    INSTALLATION INSTRUCTIONS NON-FREESTANDING MODELS ELECTRICAL CONNECTIONS Serenity Air Series Component Breakdown KEYPAD CABLE BLOWER WATER DETECTOR NEMA PLUG PROBE LIGHT CONTROL UP/HAUT OUTPUT INTPUT W/D KEYPAD AUX NEMA PLUG IMPORTANT: ONE 15 AMPS/120 VOLTS CIRCUIT; CLASS "A". LED LIGHT Aquatic...
  • Page 15 Serenity Air Series Remote Blower Option Component Breakdown KEYPAD CABLE 25’ BLOWER CABLE 25’ WATER SENSORS NEMA PLUG PROBE LIGHT CONTROL UP/HAUT OUTPUT INTPUT W/D KEYPAD AUX EXTENSION 25’ NEMA PLUG LED LIGHT IMPORTANT: ONE 15 AMPS/120 VOLTS CIRCUIT; CLASS "A". Aquatic...
  • Page 16 Serenity Air Series Remote Option Component Breakdown KEYPAD REMOTE CONTROL RECEIVER MODULE BLOWER WATER DETECTOR NEMA PLUG PROBE LIGHT CONTROL BOX UP/HAUT OUTPUT INTPUT W/D KEYPAD AUX NEMA PLUG LED LIGHT IMPORTANT: ONE 15 AMP/120 VOLTS CIRCUIT; CLASS “A”. Aquatic...
  • Page 17 Serenity Owner's Manual & Installation Guide INSTALLATION INSTRUCTIONS FREESTANDING MODELS ELECTRICAL CONNECTIONS Serenity Air Series Freestanding Component Breakdown KEYPAD RECEIVER MODULE REMOTE CONTROL CABLE 25 ’ BLOWER NOT TO BE USED WITH THIS OPTION NEMA PLUG IMPORTANT: ONE 15 AMP/120 VOLTS CIRCUIT; CLASS "A". Aquatic...
  • Page 18: Variable Speed Air Blower Remote Mounting (Non-Freestanding)

    120V vac that is GFCI protected. Remote Installation in adjacent space (closet) (example only) 4’’ Low Voltage Blower Cord to Keypad AC Outlet Check Valve Chromatherapy LED Light Water Sensor Wires 6’’ (Black and Red) Located by Drain Light Box Aquatic...
  • Page 19: Installation Of Freestanding Models

    DRAIN HOLE DRAIN HOLE 9" 9" 6" x 6" 6" x 6" BOX OUT BOX OUT TOP VIEW TOP VIEW SERENITY 37 TOP VIEW SERENITY 10 TOP VIEW Diagram 2B Pipe Concealer Cut pipes to desired length prior to assembly Aquatic...
  • Page 20 Pipes go through the floor 100% Silicone 14" 13" DRAIN HOLE DRAIN HOLE 9" 9" 6" x 6" 6" x 6" BOX OUT BOX OUT TOP VIEW TOP VIEW SERENITY 13 TOP VIEW SERENITY 11 TOP VIEW Aquatic...
  • Page 21 21 3/8” Blower Fitting Serenity 17 BLOWER ANCHOR PIN FITTING BLOWER ANCHOR PIN FITTING ANCHOR PIN ANCHOR PIN Serenity 24 Serenity 23 BLOWER BLOWER FITTING ANCHOR PIN ANCHOR PIN FITTING ANCHOR PIN ANCHOR PIN Bottom View Serenity 26 Serenity 25 Aquatic...
  • Page 22 Apply a silicone seal under the rim of the base and lay the bath down putting the pipes through the floor. Immediately remove any excess silicone. VARIABLE SPEED AIR BLOWER REMOTE MOUNTING FOR FREE- STANDING MODELS: Aquatic...
  • Page 23: Variable Speed Air Blower Remote Mounting (Freestanding)

    The location of the blower should not be air tight; a gap of 1” is recommended for good air circulation. To reduce heat loss, insulate the pipe. Sample Installations: Receiver Key Pad Serenity 10 & 37 Flow One Way Valve Blower Key Pad Receiver Serenity 10 & 37 Flow Blower One Way Valve Aquatic...
  • Page 24 INSTALLATION INSTRUCTIONS FREESTANDING MODELS Sample Installations: Receiver Key Pad Serenity 11, 13, 17, 23, 24, 25 and 26 Flow One Way Valve Blower Receiver Key Pad Serenity 11, 13, 17, 23, 24, 25 and 26 Flow One Way Valve Blower Aquatic...
  • Page 25: Serenity 27 Installation

    6. If the blower will be installed in an enclosure, you must provide a minimum 4”x 4” opening for ventilation. NOTE: Because the Serenity 27 is a one-of-a-kind bath, dimensions may vary up to several inches. Please take all measurements directly from the bath. Aquatic...
  • Page 26 Serenity 27 2” Overflow Hole Hartford One Way Valve is Under Tub Loop Flow One Way Blower Valve Hartford Loop Key Pad 2” Serenity 27 Overflow Hole One Way Valve is Under Tub Receiver Flow Blower One Way Valve Aquatic...
  • Page 27 4. Press simultaneously on buttons 1 & 2 of the remote for 4 seconds as shown in Figure 8. 5. The remote control is now synchronized and ready for use. 6. If the synchronization is not successful the first time, you should resynchronize, starting from step 2. Module and keypad Figure 8 are factory installed Aquatic...
  • Page 28: Remote Control (Non-Freestanding)

    Persons with physical Figure 9A conditions that could be affected by magnetic fields should avoid using it and/or consult with their physician. Figure 9B Aquatic...
  • Page 29: Remote Control (Freestanding)

    4. Press simultaneously on buttons 1 & 2 of the remote for 4 seconds as shown in Figure 11. 5. The remote copntrol is now synchronized and ready for use. 6. If the synchronization is not successful the first time, you should resynchronize, starting from step 2. Figure 10 Aquatic...
  • Page 30: Final System Test & Clean-Up

    5. Dulled areas can be restored to a high gloss with white or cream-colored automotive rubbing compound, followed by application of carnauba wax or white or cream automotive paste wax and buffing. 6. Major gouges require professional repair. Contact Aquatic to arrange factory-authorized repair services. Aquatic...
  • Page 31: Operation

    The drying cycle will activate 20 minutes after the bathtub is emptied even if the system was not used. The blower touch LED blinks while waiting for the purge cycle. INTEGRATED 20 MINUTE AUTOMATIC TIMER Integrated 20 minute automatic timer on the complete system. Count down starts with the last system turned on. Aquatic...
  • Page 32 Integrated 20 minute automatic timer on the system. DRYING CYCLE REMOTE CONTROL A 1 minute automatic drying cycle will start 20 minutes after the blower is turned off. The blower LED button blinks while waiting for the purge cycle. Aquatic...
  • Page 33: To Replace Led Light

    Do not attempt to remove the lens without the provided tool. Lens Tool 4. Replace your LED light (replacement LED lights can be obtained from Aquatic). LED Bulb NOTE: Do not twist LED light into socket. Use gentle pressure and push LED light into place.
  • Page 34: Tub Care

    Turn on air bath and run for approximately five minutes. Turn air bath unit off and drain tub. Aquatic recommends the above cleaning process on your air bath once a month.
  • Page 35: Cleaning

    Shut blower down and allow cleaner to soak in the bath for approximately two hours. Turn on air bath and run for approximately five minutes. Turn air bath unit off and drain tub. Aquatic recommends the above cleaning process on your air bath once a month.
  • Page 36: Water Quality Issues

    If you are on an individual well, you need to contact a water treatment company to test your water and suggest solutions if a problem is present. Aquatic...
  • Page 37 CLEAN PLUS (Aquatic Part #ST1010) manufactured by Stearns Packaging Corporation to rectify this condition. This may be obtained by contacting Aquatic at (800) 945-2726. It is recommended that you follow the instructions provided by the manufacturer with the product. Repeated use may be necessary. SUPER SYSTEMS CLEAN PLUS does not replace the necessity to purge your air system at least once a month with a low foaming detergent and bleach.
  • Page 38: Troubleshooting Guide

    WATER DETECTOR CABLE 6FT 8112SENSOR WATER DETECTOR PROBE 1136 SENSOR KEYPAD CABLE 25FT 1135 WATER DETECTOR CABLE 25FT 1118 25FT CHROMATHERAPY CABLE EXT. To indicate color, replace XX with “WH” for White, “BI” for Biscuit , “BO” for Bone Aquatic...
  • Page 39: Replacement Parts Map

    Serenity Owner's Manual & Installation Guide REPLACEMENT PARTS MAP 1c. 1a. Option Option Aquatic...
  • Page 40 AQUATIC Fax-On-Demand System: Toll Free (877) 618-7024 8101 E. Kaiser Blvd., Suite 200 • Anaheim, CA 92808 (800) 945-2726 • Fax (866) 544-5353 • www.aquaticbath.com 8MANSER / F.O.D. 9005 / Rev. 04/14...
  • Page 41 OWNER’S MANUAL & INSTALLATION GUIDE Installer: This booklet must be given to the product owner. Please add important information below. Model # ___________________________________ Purchase Date ___________________________________ Serial # ___________________________________ Distributor ___________________________________ Note: Read all instructions before proceeding with installation. All specifications are ± 3/8’’ and are subject to change without notice. Dimensions listed in inches (mm).
  • Page 42 Owner's Manual & Installation Guide ™ TABLE OF CONTENTS PRODUCT WARRANTY REGISTRATION INFORMATION IMPORTANT SAFETY INSTRUCTIONS 4 – 5 USER INFORMATION FCC CONSUMER INFORMATION AQUATIC LIMITED WARRANTY INSTALLATION INSTRUCTIONS Pre-Installation Procedures Structural Preparation 9 – 10 Plumbing Electrical Connections 11 – 13 Final System Test &...
  • Page 43: Product Warranty Registration Information

    ™ AQUATIC Product Warranty Registration Information Thank you for choosing an Aquatic bath. You have chosen one of the finest bath products in the industry! Aquatic supports your purchase with strong commitments to quality and customer satisfaction. IMPORTANT! To activate Product Warranty please register with Aquatic.
  • Page 44: Important Safety Instructions

    WARNING All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. Aquatic...
  • Page 45 Each bather should start their bath with fresh water. CAUTION: DO NOT USE HARSH ABRASIVES OR SOLVENTS FOR CLEANING THIS UNIT. INSTALLER/OWNER BEARS ALL RESPONSIBILITY TO COMPLY WITH ALL STATE AND LOCAL CODES WHEN INSTALLING THIS PRODUCT. SAVE THESE INSTRUCTIONS Aquatic...
  • Page 46: User Information

    • If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. • The user may find the following booklet prepared by the FCC helpful: “How To Identify and Resolve Radio-TV Interference Problems.” It is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No., 004-000-00345-4. Aquatic...
  • Page 47: Aquatic Limited Warranty

    You must be the Purchaser of the HotSoak. You must give prompt written notice to Aquatic at the address detailed below of any defect claim within the warranty period and provide us with any substantiation that we may reasonably request.
  • Page 48: Installation Instructions

    3. Plug in pump cord and run pump for 10 minutes. 4. Inspect the tub completely. Any defect must be reported to Aquatic prior to installation in order to have it covered by warranty. Should inspection indicate any damage or leaks, do not install the bath.
  • Page 49: Structural Preparation

    Extreme care must be taken in this type of installation to ensure the tub will come to rest entirely on the base. Apron Installation Ledge Installation - 1 Ledge Installation - 2 Sunken Installation Wall Installation WARNING: ALL ELECTRICAL CONNECTIONS SHOULD BE MADE BY A LOCALLY LICENSED ELECTRICIAN/TECHNICIAN. Aquatic...
  • Page 50: Plumbing

    INSTALLATION INSTRUCTIONS STRUCTURAL PREPARATION (CONTINUED) 6. Another installation option is that of a tile flange. Aquatic offers a factory installed tile flange for all rectangular and corner-unit tubs. 7. Install the bath unit per the instructions provided in this manual. CAUTION: THE TILE FLANGE DOES NOT SUPPORT THE TUB! A ledger board must be provided under the bath rim as indicated in the installation instructions.
  • Page 51: Electrical Connections

    BONDING WIRE: Connect a #8 bare-copper bonding wire from the pump motor/heater to the cold water plumbing or other suitable ground. Grounding is required. For built-in and custom units, install to permit access for servicing. CAUTION: Before use of the unit, test the GFCI for proper operation. Aquatic...
  • Page 52 PUMP CONTROL BOX UP/HAUT OUTPUT INTPUT W/D KEYPAD AUX HEATER NEMA PLUG PUMP PUMP MAIN BREAKER PANEL 120V-240V/60Hz NEMA PLUG IMPORTANT: 20A/120V SINGLE POLE BREAKER WITH GROUND FAULT CIRCUIT INTERRUPTER CLASS "A". (ONE 20 AMP/120 VOLT CIRCUIT.) Diagram 2 Aquatic...
  • Page 53 W/D KEYPAD AUX OUTPUT INTPUT OUTPUT INTPUT NEMA PLUG PUMP LED LIGHT NEMA PLUG MAIN BREAKER PANEL NEMA PLUG 120V-240V/60Hz IMPORTANT: 20A/120V SINGLE POLE BREAKER WITH GROUND FAULT CIRCUIT INTERRUPTER CLASS "A". (TWO 20 AMP/120 VOLT CIRCUIT.) Diagram 3 Aquatic...
  • Page 54: Final System Test & Clean-Up

    5. Dulled areas can be restored to a high gloss with white or cream-colored automotive rubbing compound, followed by application of carnauba wax or white or cream automotive paste wax and buffing. 6. Major gouges require professional repair. Contact Aquatic to arrange factory-authorized repair services. Aquatic...
  • Page 55: Operation Instructions

    HIGH LIMIT: The heater includes an exclusive “Intelligent High-Limit”. This safety circuit will not “false trip” from hot tap water. It will only turn the heater off if the thermostat fails. To reset, simply press the red button. If the high-limit trips frequently, contact Aquatic INDICATOR LIGHT: The light turns on when the heater is operating.
  • Page 56: Installation Of Electronic On/Off Timer Control

    INSTALLATION OF ELECTRONIC ON/OFF TIMER CONTROL 1. Plug the On/Off Timer Control into a dedicated 120-volt, minimum 20-Amp outlet (Speed Timer Box). 2. Wait 10-20 seconds (for self-calibration) before you depress the On/Off Button (Electronic On/Off Button). 1- Speed Timer Box Electronic On/Off Button Aquatic...
  • Page 57: Optional Chromatherapy Operation

    Do not attempt to remove the lens without the provided tool. Lens Tool 4. Replace your LED light (replacement LED lights can be obtained from Aquatic). NOTE: Do not twist LED light into socket. Use gentle pressure and LED Bulb push LED light into place.
  • Page 58: Tub Care

    SUPER SYSTEMS CLEAN PLUS (Aquatic part #ST1010) manufactured by Stearns Packaging Corporation to rectify this condition. This may be obtained by calling Aquatic, at (800) 945-2726. It is recommended that you follow the instructions provided by the manufacturer with the product. Repeated use may be necessary.
  • Page 59: Water Quality

    High iron levels may result in the formation of brown stains in the vicinity of the faucet outlets of various fixtures in the home. With bathtubs, the staining may be particularly pronounced because the aeration Aquatic...
  • Page 60 CLEAN PLUS (Aquatic part #ST1010) manufactured by Stearns Packaging Corporation to rectify this condition. This may be obtained by contacting Aquatic at (800) 945-2726. It is recommended that you follow the instructions provided by the manufacturer with the product. Repeated use may be necessary. SUPER SYSTEMS CLEAN PLUS does not replace the necessity to purge your air system at least once a month with a low foaming detergent and bleach.
  • Page 61: Troubleshooting Guide

    GFCI circuits.) 2) Fuses blown or thermal overload open. 2) Contact your electrician. 3) Locked motor shaft. 3) Contact Aquatic. 4) Motor windings burned out. 4) Contact Aquatic. 5) Defective starting switch inside single-phase motor. 5) Contact Aquatic.
  • Page 62: Replacement Parts List

    5B. (OPTION) 8020LIGHTS CHROMATHERAPY;20LEDS BULB;RND CLR 5C. (OPTION) 8LIGHTTOOL LENS REMOVAL TOOL 5D. (OPTION) 8020LIGHTS 20LEDS CHROMATHERAPY BULB 8201PUMP HEATER/MTR.;120V, 1500W; W/ PUMP To indicate color, replace XX with “WH” for White, “BI” for Biscuit , “BO” for Bone Aquatic...
  • Page 63: Replacement Parts Maps

    Serenity HotSoak Owner's Manual & Installation Guide ™ REPLACEMENT PARTS MAP (Option) (Option) (Option) Aquatic...
  • Page 64 Fax-On-Demand System: Toll Free (877) 618-7024 8101 E. Kaiser Blvd., Suite 200 • Anaheim, CA 92808 (800) 945-2726 • Fax (866) 544-5353 • www.aquaticbath.com 8MANHSK | F.O.D. 9004 | REV. 04.14...
  • Page 65 Serenity Series 1 ON/OFF BLOWER DRYING CYCLE OPTIONS 1 st Press: The blower starts STANDARD DRYING CYCLE 2 nd Press: The blower stops An automatic drying cycle will start 20 minutes after the blower is turned off. 2 BLOWER SPEED VARIATION + Press &...

Table of Contents