Subscribe to Our Youtube Channel
Related Manuals for Aquatic Elements Series
Summary of Contents for Aquatic Elements Series
- Page 1 ELEMENTS SERIES INSTALLATION AND OWNER’S MANUAL TO BE REMOVED FOR USE BY THE OCCUPANT Note: Read all instructions before proceeding with installation. All specifications are ± 1/4" and are subject to change without notice.
-
Page 3: Table Of Contents
Your whirlpool bathtub — what it is and how it works. Before Your First Use MAINTENANCE AND CARE 19-20 Tub Care Cleaning Procedures for Acrylic Surfaces WATER QUALITY 21-22 Chemical & Water Quality 21-22 TROUBLESHOOTING GUIDE REPLACEMENT PARTS LIST REPLACEMENT PARTS ORDER FORM AQUATIC LIMITED WARRANTY... -
Page 4: Product Registration Information
Your product warranty is registered and confirmed with Aquatic through the Serial Number on your unit. You do not need to contact Aquatic to confirm registration. Please fill out the information below and reference when contacting the distributor to expedite warranty claims. -
Page 5: Introduction
IMPORTANT! This product MUST BE WATER-TESTED and inspected prior to installation or warranty will be voided. Neither Aquatic nor the distributor will be responsible for removal or reinstallation costs should replacement of the bath be necessary. PLEASE CHECK ENTIRE UNIT FOR ANY DAMAGE. -
Page 6: Instructions Pertaining To A Risk Of Fire, Electric Shock, Or Injury To Persons
Elements Series Owner's Manual & Installation Guide INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING: When using this unit, basic precautions should always be followed, including the following: READ AND FOLLOW ALL INSTRUCTIONS: • WARNING: Risk of lethal electric shock. To reduce risk of electric shock, connect only to circuits protected by a Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device (RCD). - Page 7 Elements Series Owner's Manual & Installation Guide INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS Before taking your first whirlpool bath, be sure you have performed the “test run.” [See OPERATION INSTRUCTIONS on page 17.] Be sure that you are familiar with all the controls and switches and that the unit is operating properly.
-
Page 8: Pre-Installation Requirements
OR 1 ½" Galvanized roofing nail INSPECTION BEFORE INSTALLATION 1. Inspect the Aquatic jetted bath to ensure it is the correct model number, size, color, and has all features, options and accessories originally ordered. 2. If damage or shortage has occurred, notify your distributor, freight carrier, or Aquatic Customer Service Center at (800) 945-2726. -
Page 9: Before You Start
Elements Series Owner's Manual & Installation Guide BEFORE YOU START IMPORTANT: Observe all governing codes and ordinances. 1. Proper installation is your responsibility. Have a qualified technician install this bath. 2. Installation using a Ground-Fault Circuit-Interrupter (GFCI) is required. [See ELECTRICAL CONNECTIONS on pages 15-16.]... -
Page 10: Installation Requirements
Elements Series Owner's Manual & Installation Guide INSTALLATION REQUIREMENTS PRE-PLANNING ACCESS, PLUMBING & ELECTRICAL INSTALLATION 1. Building materials and wiring should be routed away from the pump body or other heat producing components. ELECTRICAL INSTALLATION: 2. Ensure that the floor is level and can support a load of 50 lbs. per square foot. (If floor is not level, shims may be needed to level the bath.) -
Page 11: Installation Instructions
Elements Series Owner's Manual & Installation Guide INSTALLATION INSTRUCTIONS FRAMING DIAGRAMS 1. Protect interior of tub throughout installation process. ELECTRICAL INSTALLATION: 2. Framing and supports will vary according to the model and type of installation selected. 3. Please refer back to the unit's Technical Data sheet for specific dimensions located at www.aquaticbath.com. -
Page 12: Deck Cutouts
Elements Series Owner's Manual & Installation Guide INSTALLATION INSTRUCTIONS DECK CUTOUTS A paper template will be enclosed with all rounded-edged models. Use the directions on the paper template for cutout dimensions. If the paper template has been lost or needs replacement, please contact Customer Service at: 800.945.2726. - Page 13 Elements Series Owner's Manual & Installation Guide INSTALLATION INSTRUCTIONS WARNING - When using electrical products, basic precautions should always be followed, including the following: DANGER - RISK OF ELECTRIC SHOCK. Connect only to a circuit protected by a Ground-Fault Circuit-Interrupter (GFCI).
-
Page 14: Framing & Installation Procedures
Skirt Installation Procedures Acrylic Units Most (not all) Aquatic integrally skirted whirlpools have color matching removable panels for alcove and corner installations. All integrally skirted units MUST BE INSTALLED BEFORE the finished floor and wall materials are installed. The skirt can be used as an access panel to the pump and controls, and is designed to have the finished wall materials butt up to the acrylic skirt frame and allows installation clearances for baseboard heaters and floor materials. -
Page 15: Electrical Connections
7. Integral On/Off Switch - For an Aquatic whirlpool supplied with a motor that has an integral on/off switch - Make certain the air tube that is connected to the motor is also connected to the on/off button nipple under the deck in order for the system to function. -
Page 16: Electrical Connections
Elements Series Owner's Manual & Installation Guide INSTALLATION INSTRUCTIONS ELECTRICAL CONNECTIONS Elements Series Whirlpool Component Breakdown Electrical Requirements:120VAC, 15 Amp GFCI outlet Aquatic... -
Page 17: Final System Test & Clean-Up
5. Dulled areas can be restored to a high gloss with white or cream-colored automotive rubbing compound, followed by application of carnauba wax or white or cream automotive paste wax and buffing. 6. Major gouges require professional repair. Contact Aquatic to arrange factory-authorized repair services. *Note: See page 20 for trademark information. -
Page 18: Operation Instructions
Elements Series Owner's Manual & Installation Guide OPERATION INSTRUCTIONS YOUR WHIRLPOOL BATHTUB — WHAT IT IS AND HOW IT WORKS. Your whirlpool bathtub is a large, extra deep bathtub with a built-in circulating system that mixes the bath water with air and pumps the mixture back into the bathtub creating the hydromassage action. -
Page 19: Maintenance And Care
SUPER SYSTEMS CLEAN PLUS manufactured by Stearns Packaging Corporation to rectify this condition. This may be obtained by contacting Aquatic at (800) 945-2726. It is recommended that you follow the instructions provided by the manufacturer with the product. -
Page 20: Cleaning Procedures For Acrylic Surfaces
Read and follow the cleaning and maintenance instructions in this manual. • To keep your Aquatic unit sparkling clean: Apply a coat of good quality automotive paste wax and buff to a high shine with a soft cloth or bath towel. Repeat every six months for easier cleaning and long lasting protection. -
Page 21: Water Quality
Elements Series Owner's Manual & Installation Guide WATER QUALITY CHEMICAL & WATER QUALITY Owners of fill and drain whirlpool bathtubs need to know basic information concerning water quality, how it affects the performance and enjoyment of the operation of their tubs, and steps that can be taken by the owner to correct related problems. -
Page 22: Water Quality
SUPER SYSTEMS CLEAN PLUS manufactured by Stearns Packaging Corporation to rectify this condition. This may be obtained by contacting Aquatic at (800) 945-2726. It is recommended that you follow the instructions provided by the manufacturer with the product. Repeated use may be necessary. SUPER SYSTEMS CLEAN PLUS does not replace the necessity to purge your whirlpool system at least once a month with a low foaming detergent and bleach. -
Page 23: Troubleshooting Guide
Elements Series Owner's Manual & Installation Guide TROUBLESHOOTING GUIDE WARNING: Always turn off power at the main electrical service panel when servicing your whirlpool. SYMPTOMS POSSIBLE PROBLEMS SUGGESTED SOLUTIONS Pump does not start: 1) GFCI or circuit breaker in OFF position. -
Page 24: Replacement Parts List
Elements Series Owner's Manual & Installation Guide REPLACEMENT PARTS LIST DESCRIPTION PART NUMBER VJET BODY 8190VJTB LJETBODY 8424100FTG WALL FITTING 8190WFTG JET TRIM 8424ESCXX BUTTON; AIR ON/OFF 8115BUTTNXX BODY; AIR BUTTON 8115BODY TUBE; ⁄ " AIR 8110TUBE ⁄ " X ⁄... -
Page 25: Replacement Parts Order Form
2. Using number and letter, choose part number and select color (or finish) on Parts List provided on page 24. 3. Fill out the form below with the selected information. Fax or send to Aquatic. 4. Call Aquatic at (800) 945-2726 for parts pricing and shipping charges. - Page 26 Elements Series Owner's Manual & Installation Guide Aquatic...
-
Page 27: Aquatic Limited Warranty
LIMITATIONS 1. Aquatic whirlpools and tubs sold for industrial, commercial or hotel use are warranted for one years, but not more than 2 years from date of manufacture, with a limited warranty that the shell will retain its structural integrity and configuration and be free of water loss due to a defect in the tub and the interior surface/ face of the whirlpool/tub is warranted against fading, blistering, cracking and delamination due to defects in the surface materials. - Page 28 Customer Service: (800) 945-2726 • www.aquaticbath.com 8MANELE 07.10.18 Aquatic...
Need help?
Do you have a question about the Elements Series and is the answer not in the manual?
Questions and answers