Advertisement
Quick Links
PM-50 Setpoint Output Quad Relay Module
Installation Guide
z Up to 250 VAC or 30 VDC
z Removable terminal block
z Relay output status LEDs
U L
FOR USE IN HAZARDOUS LOCATIONS:
C C
US
US
R
Class I, Division 2, Groups A, B, C, and D
LISTED
T4A
IND.CONT. EQ.
E317425
MODULE PACKAGE CHECKLIST
This product package should contain the items listed below. If
any items are missing or damaged, contact Red Lion immediately.
- Panel Mount Setpoint Quad Relay Module
- Accessory Pack
- Installation Guide
DIMENSIONS In inches (mm)
1.76
(44.80)
Bottom
SAFETY SUMMARY
that appear in this document or on equipment must be observed
to ensure personal safety and to prevent damage to either the
device or equipment connected to it.
No software-based device (or any other solid-state device) should
ever be designed to be responsible for the maintenance of
personnel safety or consequential equipment not equipped with
safeguards. Red Lion disclaims any responsibility for damages,
1.76
either direct or consequential, that result from the use of this
(44.80)
equipment in a manner not consistent with these specifications.
1.34
(34.10)
ORDERING INFORMATION
A listing of the entire PM-50 family of products and accessories
1
All safety related regulations, local codes as well as instructions
Do not use these products to replace proper safety interlocking.
CAUTION: Risk of Danger
Read complete instructions prior to installation and
operation of the unit.
ATTENTION : Risque de danger
Lire les instructions complètes avant l'installation et
l'utilisation de l'appareil.
WARNING - EXPLOSION HAZARD - WHEN IN
HAZARDOUS LOCATIONS, DISCONNECT POWER
BEFORE REPLACING OR WIRING MODULES.
AVERTISSEMENT - RISQUE D'EXPLOSION - DANS
LES ENDROITS DANGEREUX, DÉBRANCHEZ
L'ALIMENTATION ÉLECTRIQUE AVANT DE
REMPLACER OU DE CÂBLER LES MODULES.
This equipment is suitable for use in Class I, Division 2,
Groups A, B, C, D, or non-hazardous locations only.
Cet équipement est adapté à une utilisation dans des
endroits de classe I, Division 2, Groupes A, B, C, D, ou
dans des endroits non dangereux seulement.
PART NUMBER
DESCRIPTION
PMM000I0RL400000
Quad Setpoint Relay Output Module
can be found at www.redlion.net.
Install PM50RLY4-A
Drawing No. LP1142
Effective 08/2021
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Redlion PM-50
Summary of Contents for Redlion PM-50
- Page 1 I, Division 2, Groupes A, B, C, D, ou dans des endroits non dangereux seulement. ORDERING INFORMATION PART NUMBER DESCRIPTION PMM000I0RL400000 Quad Setpoint Relay Output Module A listing of the entire PM-50 family of products and accessories can be found at www.redlion.net.
- Page 2 Effective 08 2021 SPECIFICATIONS HARDWARE INSTALLATION Note: The PM-50 4.3 inch host accepts a maximum of 5 Installing a Module modules while the 3.5 inch host accepts a maximum of 3. Only one module from each function type (i.e. communication, WARNING - Disconnect all power to the unit before relay, analog output) can be installed.
- Page 3 1. Align the latches of the module with the host case such that – The wire used to connect the PM-50’s power supply should the backplane connector shroud on the module cover aligns be at least 22-gage wire suitably rated for the voltage, with the backplane connector opening in the host case.
- Page 4 Red Inc. All other company and product names are trademarks of Lion’s technical support. their respective owners. Support: support.redlion.net Website: www.redlion.net Inside US: +1 (877) 432-9908 Outside US: +1 (717) 767-6511 Red Lion Controls, Inc.
Need help?
Do you have a question about the PM-50 and is the answer not in the manual?
Questions and answers