Advertisement
Quick Links
ASSEMBLY INSTRUCTIONS
OCEANSIDE
OUTDOOR VINYL
SHOWER KIT
(3' X 3' ENCLOSURE)
Approximate assembly and installation time
Want to see a video on how to
assemble this product?
WWW.ZIPPITY-OUTDOOR.COM
WWW.ZIPPITY-OUTDOOR.COM
6 HRS
Scan the QR code
ASSEMBLY
INSTRUCTIONS
ZP19024
ZP19024
1
VER. 012021
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Zippity OCEANSIDE
Summary of Contents for Zippity OCEANSIDE
- Page 1 ZP19024 ASSEMBLY INSTRUCTIONS OCEANSIDE ASSEMBLY INSTRUCTIONS OUTDOOR VINYL SHOWER KIT ZP19024 (3’ X 3’ ENCLOSURE) 6 HRS Approximate assembly and installation time Want to see a video on how to assemble this product? Scan the QR code WWW.ZIPPITY-OUTDOOR.COM VER. 012021...
- Page 2 If you experience any further trouble with your product, please contact our customer service department. nychgroup.com/parts support@zippity-outdoor.com 704-892-5222 877-234-6196 Customer service agents are available to take calls weekdays from 9am- 5pm EST. If you call outside of business hours, please leave a voicemail.
- Page 3 ⅞” x 1½” x 53” ¾” Steel Screw (48) Beam (2) Shade Slat (9) Horizontal Rail (4) Shower Rod (2) Vinyl Weld 1½” x 4½” x 48” 1½” x 4½” x 48” ⅞” x 1½” x 41⅞” Glue (1) WWW.ZIPPITY-OUTDOOR.COM...
- Page 4 ZP19024 ASSEMBLY INSTRUCTIONS NOT INCLUDED WITH PURCHASE: Sold Separately Sold Separately (ZP19011) Zippity (ZP19012) ¼” x 3” Concrete ¼” x 4” Hex Head 80 lb Concrete Surface Mount Zippity Post Wedge Anchor (16) Bolt w/ Nut and Mix (2) 2-pack (2)
- Page 5 Post A. Secure to Post A with (8) ¾” Steel Screws (O). Ensure that surface mount (or post extension) is fully installed prior to securing brackets to post A. STEP 3.2 Repeat step 3.1 for Posts B (B), C (C), and D (D). WWW.ZIPPITY-OUTDOOR.COM...
- Page 6 Note: Push the Horizontal Rail tight into the back of the Rail Bracket. The screw head may cause some difficulty, but with enough force, the Horizontal Rail should pop into the Rail Bracket. WWW.ZIPPITY-OUTDOOR.COM...
- Page 7 Board as illustrated. Secure the Horizontal Rail to the Rail Brackets with (4) ¾” Steel Screws. Repeat steps 5.1 through 5.4 to assemble the other wall panel. Note: Make sure the Horizontal Rail is inserted fully over the Privacy Boards and rests inside the Rail Brackets. WWW.ZIPPITY-OUTDOOR.COM...
- Page 8 STEP 7.2 Pressure fit the Post Caps onto each Apply a small amount of Vinyl Weld Glue to the Post as shown. inside of each Decorative End Cap (F). Attach the Decorative End Caps to the end of the Beams. WWW.ZIPPITY-OUTDOOR.COM...
- Page 9 If your concrete is not level, insert 9” diameter galvanized steel washers under the lower side of the Surface Mount until it is level. Then, secure with wedge anchors. 36” deep Hammer drill will be needed for this step WWW.ZIPPITY-OUTDOOR.COM...
- Page 10 Screw comes fully out of the bottom of the Shade Slat. Place the Shade Slat on the Beam, guiding the 1¼” Steel Screws into the pre-drilled holes on each Beam, and drive them into the Beams. Repeat this process for all 9 Shade Slats. STEP 9.2 Install your shower curtain (NOT INCLUDED) according to product instructions. WWW.ZIPPITY-OUTDOOR.COM...
- Page 11 ZP19024 ASSEMBLY INSTRUCTIONS 6935 Reames Rd. Ste. K. Charlotte, NC 28216 support@zippity-outdoor.com 704-892-5222 877-234-6196 WWW.ZIPPITY-OUTDOOR.COM WWW.ZIPPITY-OUTDOOR.COM...
Need help?
Do you have a question about the OCEANSIDE and is the answer not in the manual?
Questions and answers