Outdoor vinyl shower kit (3' x 3' enclosure) (11 pages)
Summary of Contents for Zippity OCEANSIDE ZP19024
Page 1
ASSEMBLY INSTRUCTIONS OCEANSIDE ASSEMBLY INSTRUCTIONS OUTDOOR VINYL SHOWER KIT ZP19024 (3’ X 3’ ENCLOSURE) 5 HRS Approximate assembly and installation time Want to see a video on how to assemble this product? Scan the QR code WWW.ZIPPITY-OUTDOOR.COM VER. 062221 WWW.ZIPPITY-OUTDOOR.COM...
Page 2
If you experience any further trouble with your product, please contact our customer service department. parts.nychbrands.com support@zippity-outdoor.com 704-892-5222 877-234-6196 Customer service agents are available to take calls weekdays from 9am- 5pm EST. If you call outside of business hours, please leave a voicemail.
Page 3
35 5/8 in 41 in Top View 61 5/8 in 46 5/8 in 88 3/4 in 80 in 60 in 77 in 35 1/4 in 10 in 35 1/8 in 42 1/8 in 39 1/8 in Side View Front View WWW.ZIPPITY-OUTDOOR.COM...
Page 4
⅞” x 1½” x 53” ¾” Self-Drilling Stainless Steel Screw (48) Beam (2) Shade Slat (9) Horizontal Rail (4) Shower Rod (2) Vinyl Weld 1½” x 4½” x 48” 1½” x 4½” x 34 7/8” ⅞” x 1½” x 41⅞” Glue (1) WWW.ZIPPITY-OUTDOOR.COM...
Page 5
ZP19024 ASSEMBLY INSTRUCTIONS NOT INCLUDED WITH PURCHASE: Sold Separately Sold Separately (ZP19011) Zippity (ZP19012) ¼” x 3” Concrete ¼” x 4” Hex Head 80 lb Concrete Surface Mount Zippity Post Wedge Anchor (16) Bolt w/ Nut and Mix (2) 2-pack (2)
Page 6
A. Secure the brackets to post A with (8) ¾” Self-Drilling Stainless Steel Screws (O). Ensure that the surface mount (or post extension) is fully inserted prior to securing the brackets to post A. STEP 3.2 Repeat step 3.1 for Posts B (B), C (C), and D (D). WWW.ZIPPITY-OUTDOOR.COM...
Page 7
Secure the horizontal rail into the rail brackets with (4) 3/4” self-drilling stainless steel screws. Post B Post A Note: Push the horizontal rail tight into the back of the rail bracket. The screw head may cause some difficulty, but with enough force, the horizontal rail should pop into the rail bracket. WWW.ZIPPITY-OUTDOOR.COM...
Page 8
Secure the horizontal rail to the rail brackets with (4) 3/4” self-drilling stainless steel screws. Repeat steps 5.1 through 5.4 to assemble the second wall panel. Note: Make sure the horizontal rail is inserted fully over the privacy boards and rests inside the rail brackets. WWW.ZIPPITY-OUTDOOR.COM...
Page 9
STEP 7.2 Pressure fit the Post Caps onto each Apply a small amount of Vinyl Weld Glue to the post as shown. inside of each Decorative End Cap (F). Attach the decorative end caps to the ends of the beams. WWW.ZIPPITY-OUTDOOR.COM...
Page 10
If your concrete is not level, insert 9” diameter galvanized steel washers under the lower side of the surface mount until it is level. Then, secure the surface mount with wedge anchors. 36” deep A hammer drill will be needed for this step. WWW.ZIPPITY-OUTDOOR.COM...
Page 11
Place each shade slat on the beam, guiding the 11/4” stainless steel screw into the pre-drilled holes on each beam, and drive the screws in. STEP 9.2 Install your shower curtain (NOT INCLUDED) according to the product instructions. WWW.ZIPPITY-OUTDOOR.COM...