Download
Share
Print this page
  1. Manuals
  2. Brands
  3. KAMA-LABS Manuals
  4. Clock
  5. KATUSHA v2
  6. Assembly manual

KAMA-LABS KATUSHA v2 Assembly Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
www.
www.
www.K K K
ASSEMBLY MANUAL FOR
** ** **KATUSHA**
Be very careful with static
electricity. If clock not work after
build its mean that they been
damaged by static
electricity in process of
Check resistance between
+3.3
and
The resistance should be not lower
ama-
ama-
ama-L L L
KATUSHA**
KATUSHA**
CLOCK
assemble.
GND
pins of XS2.
1kOhm.
abs.com
abs.com
abs.com
v2
v2
v2
Gnd
Rx
Tx
Boot0
3.3v

Advertisement

loading

Related Manuals for KAMA-LABS KATUSHA v2

Summary of Contents for KAMA-LABS KATUSHA v2

  • Page 1 www. www. www.K K K ama- ama- ama-L L L abs.com abs.com abs.com ASSEMBLY MANUAL FOR ** ** **KATUSHA** KATUSHA** KATUSHA** CLOCK Be very careful with static electricity. If clock not work after build its mean that they been damaged by static electricity in process of assemble.
  • Page 2 1) You have a PCB with ICs: 2) Place all resistors vertical.
  • Page 3 Place photoresistor . I recommend to make h = ~20mm. 4) Place all capacitors. Be careful with polarity!
  • Page 5 C 12,C13 and Q1 should be empty!
  • Page 6 5) Place all transistors, 3.3v stabilizer and temperature sensor:...
  • Page 7 6)Place diodes and be careful with polarity:...
  • Page 9 7)Place 3 buttons:...
  • Page 10 8) Place battery holder and insert battery when clock will be fully assembled: 9) Place buzzer and be careful with polarity:...
  • Page 11 Prepare and install LEDs. LEDs should be UNDER PCB:...
  • Page 12 Place infrared receiver for remote control:...
  • Page 13 12)Place 8pin socket: 13)Prepare and place TA chip. You can use some heatsink between radiator and TA chip:...
  • Page 14 Use double-sided adhesive tape for fix radiator to PCB. Then solder TA chip to pins on PCB:...
  • Page 15 Completely assembled board should look like this.
  • Page 16 Prepare the IVLM tubes. The numeration start from most long wire and go in clockwise.
  • Page 17 Prepare IV-6 tubes, similarly. The first pin – the longest pin.
  • Page 18 17) Insert tube into holes in PCB: Put clock on the flat surface and solder the tubes.
  • Page 19 Then check the resistance between GND and +3.3V pins of XS2 again. It is should be not lower 1 kOhm. Then plug 12V DC adapter. The microcontroller starts work and you will hear short melody. LEDs start work too and should change colors.
  • Page 20 After all clock should work.
  • Page 21 CONGRATULASIONS! CONGRATULASIONS! CONGRATULASIONS!

  • Page 22: Specification

    SPECIFICATION SPECIFICATION SPECIFICATION Please note, that elements in kit and marking on PCB can be a little different. If you doubt value of element, check it with multimeter. Correct values below: Label Value Photo CR2032 3V BZR1 Buzzer C1,C6, C8-C10, 0.1uF C16, C22-C24...
  • Page 23 1000uF/16v 10uF/10v or 10uF/16v or C3, C19 10uF/25v...
  • Page 24 C4,C11 1000uF/6.3v 240p C7,C21 100uF/10v...
  • Page 25 220uF/35v 10nF NOT USED! C12, C13 6.8 pF 1uF/20v C18,C20...
  • Page 26 D1,D2 D310 1N5819 D4-D7 RGB led D8-D11 Auto led...
  • Page 27 IC1, IC6 HV518 IC9,IC11 LM7805CT MC34063AP1...
  • Page 28 DS32kHz Stabilizer 3.3V STM32F100C6 DS18B20...
  • Page 29 IC10 TA8201AK NOT USED! IC12 FT232RL Infrared receiver 220uH NOT USED!
  • Page 30 Photoresistor R3,R8,R11 R13-R15,R2 R26-R30 R4-R7,R10 9.1k...
  • Page 31 300k 4.3k 160 or R16, R17...
  • Page 32 R19,R32 3.3k R20,R25 6.8k 2.7k...
  • Page 33 3.9k...
  • Page 34 S1-S3 Buttons...
  • Page 35 T1-T16, IVLM1-1/7 Tube T17, T18 IV-6 Tube VO1-VO8 PC817...
  • Page 36 VT2-VT7 MPSA42 Power plug NOT USED! USB-port CR2032 Holder...
  • Page 37 Socket 8pin Radiator...
  • Page 38 Plastic case Screws Remote control...
  • Page 39 www. . . K K K ama ama- - - L L L abs abs. . . com ** ** **Katusha Katusha Katusha** ** ** ☺ ☺ ☺ Assembled my own hands Thanks for purchase!!! Features: * 17x Soviet IVLM1-1/7 VFD tubes (made in 1983) * 2x IV-6 VFD tubes...
  • Page 40 * Power source - DC 12V barrel plug 5.5mm/2.1mm ( "+" inside, "-" outside) * Consuming current - no more 600mA * Noiseless work * Dimensions of the clock - 197mm(7.75in) x 60mm(2.36in) x 95mm(3.74in) * Dimensions of the clock in plastic case - 207mm(8.15in) x 69mm(2.72in) x 105mm(4.13in) Button function: (from left side of clock First, Second and Third buttons)
  • Page 41 If you will press First Button shortly and then press Second Button, you can change date show parameters. Date can be shown every 5 minutes or 10, or be turned off. How to set alarm? Lightly! Similarly like date setup. Moreover, you can turn on/off alarm here. How to change parameters? Readily! 1) Press and hold Second Button...
  • Page 44 High-precision real Light sensor Socket for external Aluminum radiator time chip device Power plug for 12V DC power adapter 4x Auto leds Battery holder Buzzer Temperature sensor Infrared Receiver 4x RGB LEDs Diagnostic/debugger/ Buttons: Day of week update socket...