Lcd Section - Sony HDR-CX330 Service Manual

Ver. 1.1 2014.03
The changed portions from
Ver. 1.0 are shown in blue.

2-1-5. LCD SECTION

(Projector Model)
Refer to page 2-8 about Non Projector Model.
ns: not supplied
220
(Note 3)
218
216 (Note 5)
217
(Claws) B
B
#11
D ns
BH4600
C
(Note 1)
BT4600
(Note 1)
207
#2
: BT4600 (LITHIUM SECONDARY BATTERY)
Board on the mount position.
(See page 6-54 of Level 3)
Ref. No. Part No. Description
201 A-1998-404-A CABINET (C) ASSY (4441B), P (PJ340 (BLACK)/
201 A-1998-405-A CABINET (C) ASSY (4441W), P (WHITE)
201 A-1998-410-A CABINET (C) ASSY (4441L), P (BLUE)
201 A-1998-411-A CABINET (C) ASSY (4441B), P (PJ350/PJ350E)
201 A-1998-412-A CABINET (C) ASSY (4441B), P (PJ330E)
202 4-476-581-01 HEAT SINK (4441), P
203 A-1903-100-A FP-2106 FLEXIBLE BOARD, COMPLETE
204 4-272-358-01 CUSHION, P
205 A-1847-133-A LSV-1580A (Note 4)
206 A-1994-765-A PJ-1009 BOARD, COMPLETE
207 A-1994-888-A PD-1029 BOARD, COMPLETE (SERVICE)
208 4-209-715-01 JOYSTICK
209 4-476-577-01 INSULATING SHEET (4441)
210 4-476-573-01 KNOB (4441), FOCUS
211 4-476-580-01 RETAINER (4441), LCD
212 4-476-566-01 CUSHION (4441), LCD
213 4-476-579-01 PLATE (4441), PANEL GROUND
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
210
A
#288
#2
(Note 2)
219
Adjust the position.
LCD901
212
211
209
204
208
C
221
A
#11
202
222
(Claws)
201
Ref. No. Part No. Description
214 4-476-572-01 BUTTON (4411), PLAYBACK (PJ)
PJ340E (BLACK)) 215 4-476-561-01 CABINET (M (4441)), P
216 4-476-671-01 COVER (C (4441)), HINGE (BLACK)
216 4-476-671-11 COVER (C (4441)), HINGE (WHITE)
216 4-476-671-21 COVER (C (4441)), HINGE (BLUE)
217 X-2585-820-2 HINGE (P) (Y (4071)) ASSY
218 1-471-573-11 MAGNET (Note 5)
219 4-476-570-01 COVER (M (4441)), HINGE
220 1-889-187-11 FP-2193 FLEXIBLE BOARD (Note 3)
221 4-272-354-01 SHEET, P RADIATION
222 4-476-583-01 SHEET PJ (4441)
BH4600 1-251-928-21 SOCKET, BATTERY (Note 1)
BT4600 1-756-134-15 BATTERY, LITHIUM (SECONDARY) (Note 1)
LCD901 1-811-218-31 LCD MODULE
#2 2-635-562-31 SCREW (M1.7)
#11 3-078-890-11 SCREW, TAPPING
#30 3-086-156-11 SCREW B1.2
#288 2-187-345-21 SCREW (M1.7), P2 (Note 2)
Screw
#2: M1.7 X 4.0
215
(Black)
2-635-562-31
1.7
4.0
Note
213 Note 1: Replace the battery holder (BH4600) together when replac-
214
206 ing the lithium storage battery (BT4600) on the PD-1029
board.
(The battery holder removed once cannot be used again.)
D
When mounting these parts, mount new battery holder first
and attach new lithium storage battery next.
Note 2: This screw cannot be reused. Discard the screw removed
once in servicing. Instead, use a new screw.
Note 3: Refer to "Assembly-1: Installation Method of FP-2184/FP-
2193".
Note 4
205 PRECAUTIONS WHEN HOLDING THE PROJECTOR UNIT
(Note 4)
Very weak
(Don't hold)
Lens part
203
#30
Sheet
The projector unit (copper plate in particular) becomes hot after it is used.
When replacing a part of the projector unit, wait until it is cooled down.
Note 5: Install the magnet with
the marking oriented
as shown below.
Marking
2-7
#11: M1.7 X 4.0 (Tapping) #30: M1.2 X 3.5 (Tapping) #288: M1.7 X 2.5
(Silver) (White)
3-078-890-11 3-086-156-11
1.7
1.2
3.5
4.0
Note 1: PD-1029基板のリチウム蓄電池(BT4600) を交換する場合は
Note 2: このねじは再利用することができません。サービス対応時
Note 3: "Assembly-1: Installation Method of FP-2184/FP-2193" を参
Note 4
プロジェクターユニットを持つ際の注意
Have to wear
Weak 非常に弱い
finger stall
(Handling attention)
Lever Contact area of
レンズ部
Copper Plate
Flexible Board
シート
Terminal of
Copper Plate
Connector
プロジェクターを使用した後は，プロジェクターユニットが熱くなっています。
特に銅板の部分は高温になります。
部品を交換する時は，温度が下がってから作業を行なってください。
Note 5: マグネッ トを取付ける
際は， マ−キング面を
図の位置にあわせて
ください。
マーキング
(Black)
2-187-345-21
1.7
2.5
バッテリホルダ(BH4600) も同時に新品に交換してくださ
い。
(一度使用したバッテリホルダは再使用できません。)
部品取り付けの際は，先にバッテリホルダを取り付けてか
らリチウム蓄電池を装着してください。
に一度でも外した場合は新品のねじと交換してください。
照してください。
弱い 指サック着用
のこと
レバー
フレキ接点
銅板
コネクタ部
銅板