Table of Contents
Advertisement
RDR42x0 Professional Digital
Two-Way Radios
Communications Systems
Preparing Your Radio for Initial Use Setting Up Your Charger
1. Plug the adapter's AC connector into the AC outlet socket. (see
image A)
2. Plug the adapter's DC connector into the DC socket on the back of
the charger. (see image B)
3. Place the radio with the battery attached, or the battery alone, in the
charger. (see image C)
4. Make sure the battery contact is touching the charging terminals.
The charging process begins when the red LED light illuminates.
5. The green LED light will illuminate approximately two hours later,
indicating the battery is fully charged.
Image A
Battery Information
Charging the Battery
Your radio is powered by a Lithium-Ion (Lilon) battery. To avoid damage
and comply with warranty terms, charge the battery using only an
original RCA charger, exactly as described in the charger user guide.
When the charger's LED illuminates red, it is an indication that the
battery is being correctly charged. When the LED illuminates green,
the battery charge is complete.
Note: Charge a new battery 12 to 14 hours before initial use for best
performance. Maximum battery capacity is normally achieved after
two or three full charge / discharge cycles.
Caution: To reduce the risk of injury, use only batteries specified by
RCA Communications Systems.
– To avoid risk of personal injury, do not dispose of batteries in a fire. -
Dispose of batteries according to local recycling regulations. Do not
dispose as household waste.
– Never attempt to disassemble the battery.
– When charging a battery, keep it at a temperature between 41°F ~
104°F (5°C ~ 40°C) to ensure a full charge. Temperatures outside
this range significantly reduce battery life. The operating time (talk-
time and standby time) is noticeably shorter than normal, replace
the battery.
– Before charging a battery attached to a radio, turn the radio off to
ensure a full charge. Never leave a radio on while in the charger, as
it can damage both the battery and the radio; the charger is not a
radio stand.
Image B
Image C
Copyright © 2020 RCA Communications Systems www.RCACommunicationsSystems.com
INSTRUCTION MANUAL
– Do not cut off the power supply or remove battery while charging.
– Never charge a battery that is wet. Dry it with soft cloth prior
charging.
– The battery will eventually weaken. When the operating time (talk-
time and standby time) becomes noticeably shorter than normal,
replace the battery.
– Battery performance greatly decreases at temperatures below -4°F
(-20°C). Having a spare battery is always necessary in extremely
cold environments. A cold battery may work again when it returns to
room temperature, so keep it for later use.
– Dust on the battery contact may cause the battery not to work or
charge properly. Use a clean dry cloth to wipe it before attaching
the battery to the radio.
– Batteries with damaged contacts can be extremely dangerous. Any
battery with damage to one or more contacts should be replaced
immediately and not used under any circumstances.
Battery Storage
1. Fully charge the battery before storing it for an extended period of
time to avoid battery damage due to over-discharge.
2. Recharge a battery after three months storage to avoid reduced
battery capacity due to over-discharge.
3. When storing a battery, keep it in a dry place at room temperature.
Attaching/ Removing the Battery
1. To install the battery, please place it into the groove on
the top of the radio chassis about 5mm away from latch.
If the radio has the belt clip installed, you will have to press one side
of the clip to raise it and then slide the battery in proper position.
Press the battery with your fingers and push the battery until you
hear a latch click. The battery is now installed. (See Figure 1)
2. If you want to remove the battery from the radio, first press the
battery latch located on the bottom of the radio, and then press down
to slide the battery about 5mm to release the latch. (See Figure 2)
1
Attaching the Antenna
Screw the antenna into the connector at the top of the radio by holding
the bottom of the antenna and turn it clockwise until secure. (See
Figure 3)
2
3
3
Advertisement
Table of Contents
