Caution This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury. planer PPLS 10-750 / PPLS 10-800...
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. planer PPLS 10-750 / PPLS 10-800...
Page 4
• Wait for the cutter to stop before setting the tool down. An exposed rotating cutter may engage the surface leading We recommend using the power tool with original Trotec to possible loss of control and serious injury. accessories.
Page 5
Do not touch the mains plug with wet or damp hands. Risk of injuries caused by flying parts. Hold onto the mains plug while pulling the power cable Use a dust or chip bag or a dust extraction system. out of the mains socket. planer PPLS 10-750 / PPLS 10-800...
2. In an emergency, disconnect the device from the mains feed-in: Hold onto the mains plug while pulling the power cable out of the mains socket. 3. Do not reconnect a defective device to the mains. planer PPLS 10-750 / PPLS 10-800...
Page 8
Device handle Caution Vibration emissions can cause a health hazard if the device is used for an extended period of time or if it is not properly handled and maintained. planer PPLS 10-750 / PPLS 10-800...
• Clean the device as described in the Maintenance chapter. When the device is not being used, observe the following storage conditions: • Dry and protected from frost and heat • Ambient temperature below 45 °C • Protected from dust and direct sunlight planer PPLS 10-750 / PPLS 10-800...
Page 10
If you are using the rip fence, apply slight lateral in the vicinity. pressure on the device while guiding it over the Wear eye protection and a dust mask! workpiece. planer PPLS 10-750 / PPLS 10-800...
1. Make sure that the lift-off device (14) folds down when the device is lifted, and put the device down safely. Connecting the power cable 1. Insert the mains plug into a properly secured mains socket. planer PPLS 10-750 / PPLS 10-800...
Page 12
0 to 4 approx. 0 to 3.5 small approx. 2 to 6 approx. 2 to 5.5 medium approx. 4 to 9 approx. 2.5 to 6 large approx. 6 to 10 approx. 4 to 7.5 planer PPLS 10-750 / PPLS 10-800...
Page 13
• If required, allow the device to cool down. • If attached, disconnect the dust extraction system from the device. • Clean the device according to the Maintenance chapter. • Store the device according to the Transport and storage chapter. planer PPLS 10-750 / PPLS 10-800...
Wait for at least 3 minutes after maintenance and • Remove dust and chips from the dust bag. repair work. Only then switch the device back on. • Clean the lift-off device regularly to make sure that it moves freely. planer PPLS 10-750 / PPLS 10-800...
Page 15
The hexagonal bolts must not be loosened! The Allen wrench only serves to adjust the height of the tension element if you want to insert another type of blades. 3. Slide the tension element (17) sideways out of the cutting head (15). planer PPLS 10-750 / PPLS 10-800...
Page 16
9. Slide the tension element (17) into the cutting head (15). Make sure that the cutting edge is correctly aligned. 12. Turn the cutting head (15) by 180° and repeat the procedure with the other tension element. planer PPLS 10-750 / PPLS 10-800...
The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment We – Trotec GmbH – declare in sole responsibility that the must not be disposed of with the household waste at the end of product designated below was developed, constructed and its life.