Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PPLS 10-750
Summary of Contents for Trotec PPLS 10-750
- Page 1 PPLS 10-750 OPERATING MANUAL PLANER...
-
Page 2: Table Of Contents
This symbol indicates dangers to the health of persons due to hand injuries. PPLS 10-750 Warning This signal word indicates a hazard with an average risk level which, if not avoided, can result in serious http://hub.trotec.com/?id=41106 injury or death. Operating manual – planer PPLS 10-750... -
Page 3: Safety
The use of a dust • Do not expose power tools to rain or wet conditions. extraction system may reduce dust-related hazards. Water entering a power tool will increase the risk of electric shock. Operating manual – planer PPLS 10-750... - Page 4 Contact with electrical lines may result in fire and electric shock. Damaging a gas line may lead to an explosion. Penetrating a water line causes property damage and may cause an electric shock. • Use sharp blades only. Operating manual – planer PPLS 10-750...
- Page 5 Warning of electrical voltage We recommend using the power tool with original Trotec Make sure that you do not contact power lines. accessories. Improper handling of the device entails a risk of...
-
Page 6: Information About The Device
1. In an emergency, disconnect the device from the mains feed-in: Switch the device off and disconnect the power cable from the mains socket. Hold onto the mains plug while doing so. 2. Do not reconnect a defective device to the mains. Operating manual – planer PPLS 10-750... - Page 7 • 1 x Device PPLS 10-750 • 1 x Adapter for dust extraction • 1 x Rip fence • 1 x Rebating depth stop • 1 x Allen wrench • 1 x Open-end wrench • 1 x Manual Operating manual – planer PPLS 10-750...
-
Page 8: Transport And Storage
This can reduce the vibration load over the entire work period significantly. Operating manual – planer PPLS 10-750... -
Page 9: Start-Up
Furthermore, you can use the rip fence to pressure on the device while guiding it over the reduce the width of the planing track or of the base plate resting workpiece. on the workpiece. Operating manual – planer PPLS 10-750... - Page 10 Wear eye protection and a dust mask! Please proceed as follows to attach the chip ejector to the other side of the device: Connecting the power cable 1. Insert the mains plug into a properly secured mains socket. Operating manual – planer PPLS 10-750...
-
Page 11: Operation
Please proceed as follows to use the lift-off device: 1. Make sure that the lift-off device (13) folds down when the device is lifted, and put the device down safely. 6. Slowly guide the device along the workpiece while applying slight, even pressure. Operating manual – planer PPLS 10-750... - Page 12 Make sure to empty it on a regular basis so that a sufficient amount of dust or chips can be taken in. Caution Use a special vacuum cleaner to suck off harmful or toxic materials. Operating manual – planer PPLS 10-750...
-
Page 13: Errors And Faults
Troubleshooting tasks which require the housing to be opened extraction system to the chip ejector (2) first. must only be carried out by a specialist dealer or by Trotec. Slight smoke or odour are emitted during first use: • This is not a fault. These phenomena disappear after a brief runtime. -
Page 14: Maintenance
• Remove dust and chips from the chip ejector (2). If the chip ejector is blocked, clean it with suitable means (e.g. compressed air). • Clean the lift-off device regularly to make sure that it moves freely. Operating manual – planer PPLS 10-750... - Page 15 4. Use a suitable tool to carefully slide the blade (22) out of the tension element (16). 5. If required, clean the tension element and the blade with a dry, lint-free cloth or a brush. 6. Turn the blade over or replace it. Operating manual – planer PPLS 10-750...
-
Page 16: Disposal
You are responsible for deleting any personal data stored on the 12. Turn the cutting head (14) by 180° and repeat the waste equipment to be disposed of. procedure with the other tension element. Operating manual – planer PPLS 10-750... - Page 18 Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...