Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PPLS 10-20V
Summary of Contents for Trotec PPLS 10-20V
- Page 1 PPLS 10-20V ORIGINAL INSTRUCTIONS CORDLESS PLANER...
-
Page 2: Table Of Contents
Caution This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury. cordless planer PPLS 10-20V... -
Page 3: Safety
• When operating a power tool outdoors, use an injury within a fraction of a second. extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. cordless planer PPLS 10-20V... - Page 4 Otherwise, the blade or cutting head could be damaged. injury and fire. • During operation hold onto the power tool with both hands and make sure you stand firmly on the ground. It is safer to handle the power tool with two hands. cordless planer PPLS 10-20V...
- Page 5 Wear hearing protection. whilst adhering to the technical data. Excessive noise can lead to hearing loss. We recommend using the power tool with original Trotec accessories. Wear eye protection. With it you protect your eyes from splintering, falling Foreseeable misuse and flying pieces which could cause injuries.
- Page 6 Burn hazard when touching the cutting head. Do not touch the cutting head bare-handed! Note Wear protective gloves! If you store or transport the device improperly, the device may be damaged. Note the information regarding transport and storage of the device. cordless planer PPLS 10-20V...
- Page 7 2. In the event of an emergency, remove the battery from the device: Hold the release button of the battery and pull the battery off the device as described in chapter "Removing the battery". 3. Do not insert the battery if the device is defective. cordless planer PPLS 10-20V...
-
Page 8: Information About The Device
The device is equipped with a start lock preventing unintentional switch-on of the device. The battery comes with its own battery level indication. As a result you can check the current charging status without having to connect it to the device. Device depiction cordless planer PPLS 10-20V... - Page 9 • 1 x Adapter for dust extraction Wear hearing protection. • 1 x Rip fence Excessive noise can lead to hearing loss. • 1 x Rebating depth stop • 1 x Allen wrench • 1 x Open-end wrench • 1 x Manual cordless planer PPLS 10-20V...
-
Page 10: Transport And Storage
• The user may transport the batteries by road without any Warning additional requirements. Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy. • Dispose of the packaging material according to the national regulations. cordless planer PPLS 10-20V... - Page 11 Allow the battery (10) to cool down to room temperature. 5. Take the battery (10) out of the quick charger (8) by pressing and holding the release button (17) and pulling the battery (10) off the quick charger (8). cordless planer PPLS 10-20V...
- Page 12 3. Tighten the set screw (27) after the desired position has been set. Info If you are using the rip fence, apply slight lateral pressure on the device while guiding it over the workpiece. cordless planer PPLS 10-20V...
- Page 13 Wear eye protection and a dust mask! Please proceed as follows to attach the chip ejector to the other side of the device: 1. Detach the chip ejector (2) by turning it in the opposite direction of the arrow (LOCK). cordless planer PPLS 10-20V...
-
Page 14: Operation
Please proceed as follows to use the lift-off device: 1. Make sure that the lift-off device (19) folds down when the device is lifted, and put the device down safely. 6. Slowly guide the device along the workpiece while applying slight, even pressure. cordless planer PPLS 10-20V... - Page 15 1. Position the front base plate on the edge of the workpiece with the desired V groove (6). Make sure that the device is positioned at an angle of 45° to the workpiece. 2. Guide the device along the edge while applying even pressure. cordless planer PPLS 10-20V...
-
Page 16: Available Accessories
Shutdown • Check the quick charger for damage. If the quick charger Warning of electrical voltage is damaged, stop using it. Contact the Trotec customer Do not touch the mains plug with wet or damp hands. service. • Switch off the device. -
Page 17: Maintenance
This indicates ageing of the drive belt. It must be Notes on maintenance exchanged. Contact the Trotec customer service. Inside the device, there are no parts that need to be maintained • Check whether the blades are correctly inserted. If or lubricated by the user. - Page 18 5. Use a suitable tool to carefully slide the blade (29) out of the tension element (22). the tension element (22). 6. If required, clean the tension element and the blade with a dry, lint-free cloth or a brush. 7. Turn the blade over or replace it. cordless planer PPLS 10-20V...
- Page 19 Make sure that the cutting edge is correctly aligned. 13. Turn the cutting head (20) by 180° and repeat the procedure with the other tension element. 11. Bring the protective cover (21) of the cutting head into the correct position by letting go of it. cordless planer PPLS 10-20V...
-
Page 20: Disposal
The Annex II, Part 1, Section A addresses can be obtained from your municipality or local Herewith, we – Trotec GmbH– declare that the machinery administration. For further return options provided by us please designated below was developed, constructed and produced in refer to our website https://de.trotec.com/shop/. - Page 21 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...