Electrical Connections - Panasonic CQ-C1120U Operating Instructions Manual

E
Installation
N
(Continued)
G
L
I
S
❐ Preparation
H
Warning: If your car is equipped with air bag
17
and/or anti-theft systems, specific procedures
may be required for connection and disconnec-
tion of the battery to install this product.
Before attempting installation of this electronic
component, contact your car dealer or manufac-
turer to determine the required procedure and
strictly follow their instructions.
FAILURE TO FOLLOW THE PROCEDURE MAY
RESULT IN THE UNINTENDED DEPLOYMENT OF
AIR BAGS OR ACTIVATION OF THE ANTI-THEFT
SYSTEM RESULTING IN DAMAGE TO THE VEHI-
CLE AND PERSONAL INJURY.
• Disconnect the cable from the negative battery
terminal (see warning and caution below).
• Remove Mounting Collar q and Trim Plate u from the
main unit temporarily, which are already mounted at
shipment.*
Caution: Various settings that have been stored in the
memory in other on-board equipment (car navigation
etc.) may be lost if the battery terminals are discon-
nected.
Therefore, we recommend to make a record of or to
back up the settings before disconnecting the termi-
nals.
After completing installation of the main unit, set the
equipment again according to the record.
• Unit should be installed in a horizontal position with the
front end up at a convenient angle, but not more than 30°.
Less than 30
❐ Dashboard Installation
Installation Opening
This unit can be installed in any dashboard having
an opening as shown below. The dashboard should
be 3 ⁄ 16" (4.75 mm)–7 ⁄ 32" (5.56 mm) thick in
order to be able to support the unit.
2 3 /
"
32
(53 mm)
7 /
5 "
32
(182 mm)
28
CQ-C1200U/C1120U/C1110U/C1100U
❐ Installation Hardware
No. Item Diagram
Mounting Collar*
q
(FX0214C316ZA)
Hex. nut (5 mmø)
w
(YJN994C002ZA)
Rear support strap
e
(YFG044C002ZA)
Tapping screw (5 mmø×16 mm)
r
(XTT5+16AFK)
Mounting Bolt (5 mmø)
t
(YEJV014C002A)
Power Connector
y
(YEAJ02877)
Trim Plate*
u
(YFC054C063ZA)
Dismounting Plate
i
(YFX214C323ZA)
(a) Using the rear support strap e
Fire wall of car
r Tapping screw
(5 mmø×16 mm)
3 mmø
w Hex. nut
(5 mmø)
e Rear support strap
t Mounting bolt (5 mmø)
q Mounting collar
°
(b) Using the rubber cushion (option)
Rear support bracket
Rubber cushion (option) (provided on the car)
t Mounting bolt
(5 mmø)
q Mounting collar
Cautions:
¡We strongly recommend that you wear gloves for installation work to protect yourself from injuries.
¡When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your
Q'ty
hands and fingers.
1
First complete the electrical connections, and
then check them for correctness.(
1
The included Mounting Collar q is
designed specially for this unit. Do
not use it to attach any other model.
1
1
1
1
y Power Connector
1
2
Mounting Springs ( C )
Engage the Mounting
Springs ( C ) in the
mounting holes of the
Mounting Collar q
firmly.
Mounting Spring
Insert Mounting Collar q into the dash-
1
board, and bend the mounting tabs out
a page 30)
with a screwdriver.
The tabs to be bent vary depending on
the car. To securely install the unit, fully
bend a number of the tabs so that there
is no rattling.
Example:
q Mounting
Collar
Mounting Holes
t Mounting Bolt
Establish the rear connection of the unit.
2
After fixing Mounting Bolt t and Power Connector
y, fix the rear of the unit to the car body by either
method (a) or (b) shown the previous page.
3
Insert Trim Plate
4
After installation reconnect the negative
(–) battery terminal.
Mounting
Hole
CQ-C1200U/C1120U/C1110U/C1100U
E
N
G
L
I
S
H
18
Tab
u
.
29