Table of Contents
Advertisement
E
Power and Sound Controls
N
G
L
I
S
Power
H
Turn the key in the ignition until
1
the accessory indicator lights.
Power on: Press [SRC] (POWER).
Power off: Press [SRC](POWER)
again and hold.
A C C
O N
APM
POWER
Volume
Turn the knob clockwise to increase volume,
and counterclockwise to decrease volume.
Volume level (0 to 40)
(default: 18)
Up
Down
Mute
Press [MUTE] to mute the sound completely.
MUTE
ST
lights
Press [MUTE] again to cancel.
Notes:
• If no operation takes place for more than 2 seconds in the SQ mode, the display returns to the regular mode.
Settings of SQ, bass/treble are influenced one another. If the influence mentioned above causes distortion to audio signal,
•
readjust bass/treble or volume
(➡
page 13)
.
• CQ-C1100U has no remote control function.*
12
CQ-C1200U/C1120U/C1110U/C1100U
Display Change
Press [DISP] (display) to switch to the clock display.
When the power is off:
No display
Clock display
Note: "AdJ" is displayed when the clock is not adjusted.
➡
(
page 13)
Remote control sensor
(➡
page 18)*
(only for CQ-C1200U/C1120U/C1110U)
CQ-C1200U
D
•
M
TUNE
TRACK
CLOCK
REP
7
8
9
10
11
12
SCAN
MUTE
MUTE
1
2
3
4
5
6
SQ
SQ
SQ indicator
SQ (Sound Quality)
SQ is a function that can call up various sound types at
the touch of button in accordance with your listening
music type.
Press [SQ] to select a sound type as follows:
(default)
SQ -- (default)
flat frequency response:
does not emphasize.
SQ - 1 (ROCK)
speedy and heavy sound:
exaggerates bass and treble.
SQ - 2 (POP)
wide-ranged and deep sound:
slightly emphasizes bass and treble.
SQ - 3 (VOCAL) clear sound:
emphasizes middle tone and
slightly emphasizes treble.
Note: If no operation takes place for more than 5 sec-
onds in audio mode (2 seconds in volume mode), the
display returns to the regular mode.
Audio Mode
(Bass/Treble/Balance/Fader/Sub Woofer)
q
Push [SEL] to select the audio mode.
Volume
Bass
Treble
Regular mode
Sub Woofer
Fader
Balance
(Only for CQ-C1200U)
CQ-C1200U
APM
POWER
7
8
9
10
11
MUTE
1
2
4
5
3
w
Turn [VOLUME] clockwise or counterclockwise
to change each level.
Bass:
default: 0 dB
Adjustable range: –12 to +12 (by 2 dB step)
Treble:
default: 0 dB
Adjustable range: –12 to +12 (by 2 dB step)
Balance:
R (right speaker) or L (left speaker)
Adjustable range: 1 to 15 (by 1 step) Balance center
Fader:
(default)
F (front speaker) or R (rear speaker)
Adjustable range: 1 to 15 (by 1 step)
Fader center
(default)
Sub Woofer:
(Only for CQ-C1200U)
default: 4
Adjustable range (level): MUTE (0) to 7
Clock Setting
The 12-hour system is used for the clock.
Initial Time
q
Press [DISP] (clock).
"AdJ" is displayed when the clock is not
Push
adjusted.
[k TUNE], [l TUNE] (Hours, minutes)
D
•
M
TUNE
TRACK
CLOCK
REP
12
SCAN
6
SQ
[DISP] (clock)
Hours
w
Press and hold [DISP] (clock) for more than 2
seconds.
(Hours blink.)
e
Press [k TUNE] or [l TUNE].
(Hours set.)
Minutes
r
Press [DISP] (clock).
(Minutes blink.)
t
Press [k TUNE] or [l TUNE].
(Minutes set.)
y
Press [DISP] (clock).
(End.)
Note: Press and hold [k TUNE] or [l TUNE] to
change numbers rapidly.
Time Reset
Press and hold [DISP] (clock) for more than
2 seconds to activate the time setting mode to
reset the time. Then, repeat steps e to y.
CQ-C1200U/C1120U/C1110U/C1100U
E
N
G
L
I
S
H
2
1
13
Hide quick links:
Advertisement
Table of Contents
