Download Print this page
Bitspower BP-VG3090CFA Instruction Manual

Bitspower BP-VG3090CFA Instruction Manual

Design for igame geforce rtx 3090 advanced series

Advertisement

Quick Links

Design for iGame GeForce RTX 3090 Advanced series
Accessories
1
BP-VG3090CFA
1 SET
2
1.0 mm Thermal pad
4 PCS
3
2.5 mm Thermal pad
2 PCS
4
2.0 mm Thermal pad
2 PCS
5
Back plate
1 PC
6
M2.5 x 8 screw
17 PCS
7
Jumper
1 PC
8
M2.5 Nut
1 PC
9
2 PCS
Washer
Please tear off the protective film on the mirror plate.
1
Digital RGB PIN on
motherboard or
equipment.
1
2
BPTA-DRGBMFC
motherboard
DRGB Multi Function Controller
(Not included)
[ 1 ]
V2
7
8
2
other
9
instruction manual
1
2
3
4
5
6

Advertisement

loading
Need help?

Need help?

Do you have a question about the BP-VG3090CFA and is the answer not in the manual?

Questions and answers

Summary of Contents for Bitspower BP-VG3090CFA

  • Page 1 Design for iGame GeForce RTX 3090 Advanced series Accessories BP-VG3090CFA 1 SET 1.0 mm Thermal pad 4 PCS 2.5 mm Thermal pad 2 PCS 2.0 mm Thermal pad 2 PCS Back plate 1 PC M2.5 x 8 screw...
  • Page 2 Applying the thermal pad and thermal paste on correct positions. Using appropriate amount of thermal paste. 1.0 mm Thermal pad 2.0 mm Thermal pad 2.5 mm Thermal pad [ 2 ]...
  • Page 3 PC components, please perform a 24-hour leaking test with only the pump connected to the power supply. Bitspower reserves the right to change the product design and interpretations. These are subject to change without notice. Product colors and accessories are based on the actual product.
  • Page 4 使用說明書 Design for iGame GeForce RTX 3090 Advanced series 配件 BP-VG3090CFA 1 組 1.0 mm 導熱墊片 4 片 2.5 mm 導熱墊片 2 片 2.0 mm 導熱墊片 2 片 背板 1 片 M2.5 x 8 螺絲 17 支 跳接帽 1 個...
  • Page 5 導熱墊片和導熱膏的正確應用位置 適量使用導熱膏 1.0 mm 導熱墊片 2.0 mm 導熱墊片 2.5 mm 導熱墊片 [ 5 ]...
  • Page 6 注意 跑水前,請先確認所有零件已安裝在正確的位置上,在不開主機,單開水泵的情况下,進行 24 小時的跑水測試, 確保無漏水情况後再開主機,避免發生漏水而導致電腦零件的損壞。 本公司保留對產品的設計更改以及解釋的權力,如有更動恕不另行通知,產品顏色與配件以實物為準。 當使用測氣產品測試水路時 , 為避免由于壓力過大導致產品損壞 , 輸入的壓力請不要超過 0.5kg/cm2 (Bar), 如因壓 力過大造成產品損壞 , 將由客戶自行承擔 . 嚴禁客戶在水路有水及水泵開啟的情況下進行氣體飽壓測試。 Bitspower 建議消費者使用蒸餾水、純凈水,加入 Bitspower 的染劑作為水冷液使用;如客戶自行選購的水冷液導 致電鍍層剝落、水道堵塞、水泵轉動不正常、水箱管破裂或密封圈變型以致漏水等及其它不可抗力之問題時,消費 者自行承擔相關產品責任。未注水前,請勿啟動水泵電源。 [ 6 ]...
  • Page 7 使用说明书 Design for iGame GeForce RTX 3090 Advanced series 配件 BP-VG3090CFA 1 组 1.0 mm 导热垫片 4 片 2.5 mm 导热垫片 2 片 2.0 mm 导热垫片 2 片 背板 1 片 M2.5 x 8 螺丝 17 支 跳接帽 1 个...
  • Page 8 导热垫片和导热膏的正确应用位置 适量使用导热膏 1.0 mm 导热垫片 2.0 mm 导热垫片 2.5 mm 导热垫片 [ 8 ]...
  • Page 9 注意 跑水前,请先确认所有零件已安装在正确的位置上,在不开主机,单开水泵的情况下,进行 24 小时的跑水测试, 确保无漏水情况后再开主机,避免发生漏水而导致电脑零件的损坏。 本公司保留对产品的设计更改以及解释的权力,如有更动恕不另行通知,产品颜色与配件以实物为准。 当使用测气产品测试水路时 , 为避免由于压力过大导致产品损坏 , 输入的压力请不要超过 0.5kg/cm2 (Bar), 如因压 力过大造成产品损坏 , 将由客户自行承担 . 严禁客户在水路有水及水泵开启的情况下进行气体饱压测试。 Bitspower 建议消费者使用蒸馏水、纯净水,加入 Bitspower 的染剂作为水冷液使用;如客户自行选购的水冷液导 致电镀层剥落、水道堵塞、水泵转动不正常、水箱管破裂或密封圈变型以致漏水等及其它不可抗力之问题时,消费 者自行承担相关产品责任。未注水前,请勿启动水泵电源。 [ 9 ]...