Related Manuals for RJG Lynx LE‑R‑50‑REVB
Summary of Contents for RJG Lynx LE‑R‑50‑REVB
- Page 1 PRODUCT MANUAL PRODUCT MANUAL Lynx™ 50‑Inch Stroke/ Velocity Sensor LE‑R‑50‑REVB Training and Technology for Injection Molding...
- Page 2 PRINT DATE 08.24.2021 REVISION NO.
-
Page 3: Table Of Contents
PRODUCT MANUAL Lynx™ 50‑Inch Stroke/Velocity Sensor LE‑R‑50‑REVB INTRODUCTION DISCLAIMER PRIVACY ALERTS ABBREVIATIONS PRODUCT DESCRIPTION APPLICATIONS STROKE (SCREW) POSITION VELOCITY (SPEED) MEASUREMENT OPERATION DIMENSIONS INSTALLATION INSTALLATION OVERVIEW INSTALLATION SPECIFICATIONS REQUIREMENTS MOUNTING MOUNTING (RETROFIT) CONNECTIONS ALTERNATE INSTALLATIONS PREFERRED ALTERNATE INSTALL ALTERNATE INSTALL Product Manual | Lynx™... - Page 4 PRODUCT MANUAL Lynx™ 50‑Inch Stroke/Velocity Sensor LE‑R‑50‑REVB MAINTENANCE CLEANING WARRANTY RJG, INC. STANDARD PRODUCT WARRANTY PRODUCT DISCLAIMER TROUBLESHOOTING COMMON INSTALLATION ERRORS CUSTOMER SUPPORT RELATED PRODUCTS COMPATIBLE PRODUCTS LYNX CABLES CE‑LX5 EDART PROCESS CONTROLLER COPILOT SYSTEM Lynx™ 50-Inch Stroke/Velocity Sensor LE-R-50-REVB | Product Manual...
-
Page 5: Introduction
This guide must be kept available for reference at all times. DISCLAIMER PRIVACY Inasmuch as RJG, Inc. has no control Designed and developed by RJG, Inc. over the use to which others may put Manual design, format and structure this material, it does not guarantee that copyright 2020 RJG, Inc. - Page 6 Lynx™ 50-Inch Stroke/Velocity Sensor LE-R-50-REVB | Product Manual...
-
Page 7: Product Description
The Lynx™ 50‑inch stroke/velocity sensor LE‑R‑50‑REVB is a molding machine‑mountable, linear position/velocity sensor designed for use with the RJG, Inc. eDART® and CoPilot® systems. The stroke/ velocity sensor can be used to monitor standard screw position and speed on most injection molding machines. -
Page 8: Dimensions
DIMENSIONS Lynx™ 50-Inch Stroke/Velocity Sensor LE-R-50-REVB | Product Manual... -
Page 9: Installation
Read all instructions before installing The stroke/velocity sensor cable NOTES must enter the cable bushing hardware and related components. Contact straight to eliminate wear on the RJG, Inc. Customer Support for any cable prevent erroneous readings. questions regarding installation. Follow... -
Page 10: Mounting
MOUNTING Mount the LE‑R‑50‑REVB on the molding machine injection unit sled using the two included 10‑24 x 2” cap screws. Lynx™ 50-Inch Stroke/Velocity Sensor LE-R-50-REVB | Product Manual... -
Page 11: Mounting (Retrofit)
Mount adapter plate on the molding the LE‑R‑50‑REVB as a replacement for machine injection unit sled using the four the LE‑R‑50‑REVA. Contact RJG to order a included 8‑32 x 1/2” screws in place of template to create the adapter plate. the previous LE‑R‑50‑REVA monting plate. -
Page 12: Connections
INSTALLATION SPECIFICATIONS (continued) CONNECTIONS Strain‑relieve the Lynx cable so The LE‑R‑50‑REVB is connected to the NOTES that movement of the sled does not eDART or CoPilot system with a single Lynx place strain on the LE‑R‑50‑REVB cable (CE‑LX5‑4M‑F90) featuring a 90° connector. -
Page 13: Alternate Installations
ALTERNATE INSTALLATIONS In the event that the recommended installation method is not possible, the LE‑R‑50‑REVB may be installed using either the preferred alternate installation, or if also not possible, the alternate installation. Do not use either of the following two methods if the recommended installation method is possible. - Page 14 Lynx™ 50-Inch Stroke/Velocity Sensor LE-R-50-REVB | Product Manual...
-
Page 15: Maintenance
CLEANING the same results as those described here will be obtained. Nor does RJG, Inc. Keep the stroke/velocity sensor’s cable guarantee the effectiveness or safety clean and free from debris to ensure a long of any possible or suggested design for service life. - Page 16 Lynx™ 50-Inch Stroke/Velocity Sensor LE-R-50-REVB | Product Manual...
-
Page 17: Troubleshooting
TROUBLESHOOTING COMMON INSTALLATION ERRORS 2. Cable is Angled 1. Cable Interference The stroke/velocity sensor is installed so The stroke/velocity sensor is installed that the cable exit/enters the sensor body so that there is interference along the at an angle instead of straight ( cable path. -
Page 18: Customer Support
CUSTOMER SUPPORT Contact RJG’s Customer Support team by phone or email. RJG, Inc. Customer Support P: 800.472.0566 (Toll Free) P: +1.231.933.8170 email: CustomerSupportGroup@rjginc.com www.rjginc.com/support Lynx™ 50-Inch Stroke/Velocity Sensor LE-R-50-REVB | Product Manual... -
Page 19: Related Products
RELATED PRODUCTS COMPATIBLE PRODUCTS LYNX CABLES CE‑LX5 The Lynx sensor cable ( at right) is a polyeurethane‑coated cable suited for the heat and stress found in injection molding environments. The cable is available in lengths from 11.8– 472.4” (0,3– 12 m), and can be ordered with straight or 90°... - Page 20 Lynx™ 50-Inch Stroke/Velocity Sensor LE-R-50-REVB | Product Manual...
- Page 22 P +39 335 178 4035 P +01 231 947‑3111 sales@it.rjginc.com F +01 231 947‑6403 it.rjginc.com sales@rjginc.com www.rjginc.com MEXICO RJG MEXICO SINGAPORE RJG (S.E.A.) PTE LTD Chihuahua, Mexico Singapore, Republic of P +52 614 4242281 Singapore sales@es.rjginc.com P +65 6846 1518 es.rjginc.com sales@swg.rjginc.com en.rjginc.com...
Need help?
Do you have a question about the Lynx LE‑R‑50‑REVB and is the answer not in the manual?
Questions and answers