Page 1
ASCD 18-W2; ASCD 18-W4 Repair instructions ASCD 18-W2 ASCD 18-W4 C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 1 of 33 FEIN retains all rights of disposal, such as copying and circulation...
6. Disassembly 7. Assembly 8. Troubleshooting 9. Connection diagram C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 2 of 33 FEIN retains all rights of disposal, such as copying and circulation...
7 115 01 00 94 0 ASCD 18-W4 7 115 02 00 94 0 C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 3 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Up-to-date test data for all models can be found on the FEIN Extranet (Customer Service → Repair Guides). Lubricants The lubricants and container sizes available from FEIN can be found on the FEIN Extranet (Customer Service → Repair Guides). Lists of spare parts Lists of spare parts and exploded views are available online at www.fein.com...
Outside Germany, the regulations applicable in the relevant country must be observed! C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 5 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Slotted screwdriver (small) Circlip pliers (angled) Soldering rod Torque wrench C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 6 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Tool holder Grease 0 40 119 0500 7 Tool holder C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 7 of 33 FEIN retains all rights of disposal, such as copying and circulation...
3. Unscrew the four screws (4). - Cross-tip screwdriver C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 8 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 9
2. Remove switch (2), gearbox (3) and toggle switch (4) from motor housing. - Torx T10 C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 9 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 10
1. Remove the eight pressure pieces (1) from the motor housing halves. C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 10 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 11
2. Remove disc (2), spring (3) and sleeve (3). - Circlip pliers (angled) - Slotted screwdriver (small) C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 11 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 12
The gearbox can then be pulled out of the motor housing. C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 12 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 13
1. Remove disc (1) from housing with a slotted screwdriver. Tool: - Slotted screwdriver C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 13 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 14
2. Pull armature (3) off brush holder set. - Assembly aid C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 14 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 15
1. Unsolder the two cables (1) from switch. Tool: - Soldering rod C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 15 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 16
During assembly/disassembly, only touch magnet on outer race. C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 16 of 33 FEIN retains all rights of disposal, such as copying and circulation...
4. Coat inside (4) of tool holder with 1g of grease. C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 17 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 18
Risk of crushing due to strong pull of magnet. During assembly/disassembly, only touch magnet on outer race. C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 18 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 19
3. Solder black cable (4) of brush holder set on to position M2 on switch. C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 19 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 20
1. Lift the four tension springs (1) of brush holder on to notches provided (2) with hook. Tool: - Assembly aid C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 20 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 21
1. Push brushes to the outside to free up the passage. Tool: - Assembly aid C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 21 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 22
1. Position brush holder set (1) on armature (2). C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 22 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 23
1. Lift the four tension springs (1) of brush holder set back on to carbon brushes with hook. Tool: - Assembly aid C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 23 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 24
1. Fit the eight pressure pieces (1) in motor housing. C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 24 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 25
2. Insert switch (2) into motor housing half. Note cable routing (3). C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 25 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 26
2. Insert the gearbox (2) and toggle switch (3) in the motor housing half. 3. Route the cable (4) as shown. C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 26 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 27
Important: Groove (6) of brush holder set must be inserted above raised section of housing (7). C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 27 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 28
1. Screw down motor housing half (1) with seven screws [0.7 Nm – 1.1 Nm]. Tool: - Torx T10 - Torque wrench C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 28 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 29
- Cross-tip screwdriver - Torx T10 - Torque wrench C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 29 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 30
3. Position disc (3) on spring. 4. Position circlip (4) and press in. C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 30 of 33 FEIN retains all rights of disposal, such as copying and circulation...
Page 31
If the tool does not start up during the function test, there is a risk that the battery will be overloaded and destroyed (short-circuit) because the motor is blocked by incorrect installation! C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 31 of 33 FEIN retains all rights of disposal, such as copying and circulation...
ASCD 18-W2; ASCD 18-W4 8. Troubleshooting C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 32 of 33 FEIN retains all rights of disposal, such as copying and circulation...
ASCD 18-W2; ASCD 18-W4 9. Connection diagram C-SC_CSSM Version 1.0 2014-07-09 All rights reserved by FEIN, especially in case of industrial rights registration. Page 33 of 33 FEIN retains all rights of disposal, such as copying and circulation...